⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Stepper Motor General Question

I want to drive a small machine at 120 rpm using a stepper motor. I could run it direct or by a pully to give a reducti...
4 comments posted 16yrs
posted by jpeterbell
4 comments posted 16yrs posted by jpeterbell

Spindle Bearings

Evening all, Im rebuilding a spindle for a precision drill / sort of jig bore. Its 'home made' from a SIP Inspection Mi...
1 comments posted 16yrs
posted by david.sanderson
1 comments posted 16yrs posted by david.sanderson

MAPP gas

I have previously bemoaned the fact that MAPP gas is no longer available - the Canadian factory/refinery which produced...
2 comments posted 16yrs
posted by zenadsl6186
2 comments posted 16yrs posted by zenadsl6186

Helicoil versus Time Sert

I've used helicoils for years and always got satisfactory service from them. However I recently stumbled upon Time Sert...
3 comments posted 16yrs
posted by someone
3 comments posted 16yrs posted by someone

First time cutting a thread ?(Novice)

This is the first time I have attempted to cut a thread although I have done some simple lathe work in the past on a Su...
15 comments posted 16yrs
posted by Donwill.seesig
15 comments posted 16yrs posted by Donwill.seesig

Anyone know what's happened to J&L?

J&L or MSC/J&L, as appropriate in the UK, seem to have got a dead web site. Window shopping via the catalogue is all ve...
24 comments posted 16yrs
posted by randm
24 comments posted 16yrs posted by randm

Old throatless shear

Hi everyone I've bought a very large and very old (1950s?) throatless shear. The makers mark is cast into the machine a...
3 comments posted 16yrs
posted by mjangling
3 comments posted 16yrs posted by mjangling

In praise of the ceramic chip forge

Before I moved house, I had a ceramic chip forge running off mains gas. Useful but not used very often. Here we have no...
26 comments posted 16yrs
posted by andrew
26 comments posted 16yrs posted by andrew

Steel rod, unusual sizes

I need a source of 2.6mm steel rod - silver steel preferably, but mild would do. Only needs to be 6 inches long at mini...
25 comments posted 16yrs
posted by seesigfor
25 comments posted 16yrs posted by seesigfor

ID mystery lathe?

I saw this at my local auction: http://i48.photobucket.com/albums/f234/bugbear33/misc/lathe_lead.jpg What on earth is i...
4 comments posted 16yrs
posted by bugbear
4 comments posted 16yrs posted by bugbear

Air-con pump

I was down at the scrappy the other day and noticed what looked like a NEW Air-con pump (ex automotive I assume) lying...
4 comments posted 16yrs
posted by poundeater
4 comments posted 16yrs posted by poundeater

Toolpost screws

As usual when I post I would be pleased to receive some advice. I need about 30 square headed toolpost screws, 5/16=94...
17 comments posted 16yrs
posted by harriscamley
17 comments posted 16yrs posted by harriscamley

Sroll saw - cutting non ferrous metals

I've just been given a PowerCraft PFZ-400RN Scroll saw which has one mention in the booklet that it will cut plastics a...
4 comments posted 16yrs
posted by alan.dawes
4 comments posted 16yrs posted by alan.dawes

Anyone need a complete 1.2 GHz PC?

Hi folks, I've been sorting and rationalising my computer equipment. I've built two PCs from parts. One I'll be keeping...
0 comments posted 16yrs
posted by cdt22NOSPAM
0 comments posted 16yrs posted by cdt22NOSPAM

MEC Brown coolant pump repair

In a fit of enthusiasm I decided to resurrect the coolant pump on my MEC Brown Pedrazoli cut off saw. It's actually a f...
2 comments posted 16yrs
posted by andrew
2 comments posted 16yrs posted by andrew