⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Results of my query

I recently asked for comments as the best way to glue a stack of 40+ brass and steel pieces together. Further to "Peter...
3 comments posted 16yrs
posted by poundeater
3 comments posted 16yrs posted by poundeater

Boring in the lathe - imbecile question

I've got a chunk of round aluminium bar of 60mm diameter, 100mm long. I want to bore this out to make a cup shape with...
24 comments posted 16yrs
posted by creffield
24 comments posted 16yrs posted by creffield

Wanted: Myford 7 clutch pulley

The smaller V-pulley on my Myford clutch is broken where someone tried to remove it from the shaft. Before I buy a new...
0 comments posted 16yrs
posted by creffield
0 comments posted 16yrs posted by creffield

Harrison mill wiring diagram

Hi All I've finally completed building a rotary phase converter to power the coolant pump and table feed motor on my Ha...
0 comments posted 16yrs
posted by tobybishop
0 comments posted 16yrs posted by tobybishop

Shed roofing

How long does one expect roofing felt to last? The reason I ask is that there appears to have been seepage through the...
23 comments posted 16yrs
posted by Multum.In
23 comments posted 16yrs posted by Multum.In

Tracking solar and a mount for sterling engines

I have a model of tracking solar on equatorial mount that I have slowly refined. I don't have time to play with it anym...
0 comments posted 16yrs
posted by brian
0 comments posted 16yrs posted by brian

Broken tap

I broke a carbon steel M8 tap in mild steel, and tried various ways to get it out. Eventually I put the workpiece on an...
0 comments posted 16yrs
posted by zenadsl6186
0 comments posted 16yrs posted by zenadsl6186

Inverter Failure

As those with long memories might recall I run my 3HP CVA lathe via a 240-415 transformer and a 415volt 3 phase ACS 300...
12 comments posted 16yrs
posted by charlesp
12 comments posted 16yrs posted by charlesp

Model engineering metals?

1) Silver steel 2) Ground flat stock 3) Key steel Are these used much in industry? Why I ask, is that I was looking for...
17 comments posted 16yrs
posted by zenadsl6186
17 comments posted 16yrs posted by zenadsl6186

What is this group?

It seems to be more about tools than models
6 comments posted 16yrs
posted by eaves
6 comments posted 16yrs posted by eaves

Taper Roller Bearing Preloading

Hi I am a student undergoing a training program. And I have an assignment on taper roller bearings. Now since these bea...
10 comments posted 16yrs
posted by aagoyle1.4836cn
10 comments posted 16yrs posted by aagoyle1.4836cn

Adjustable reamer pilots

I've recently aquired a set of pilot guides for adjustable reamers From H6 to H15. Now I don't have reamers in all of t...
0 comments posted 16yrs
posted by johnmanders
0 comments posted 16yrs posted by johnmanders

Cone / step pulley wanted

Hello All I am looking for a step pulley for A size vee belt. 3 or 4 steps would be fine, alloy or iron, bore unimporta...
1 comments posted 16yrs
posted by sharkface.pilot
1 comments posted 16yrs posted by sharkface.pilot

Still looking for a mill!

Kondia Turret mills have come up recently plus Condor. Anyone have any experience of these makes? A Bridgeport is what I...
5 comments posted 16yrs
posted by poundeater
5 comments posted 16yrs posted by poundeater

Taper roller

I want to install some taper roller bearings on a shaft. My problem is that the force-bearing faces are on the outside...
10 comments posted 16yrs
posted by zenadsl6186
10 comments posted 16yrs posted by zenadsl6186