⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

Linkage rebuild

Hi, I,m renovating a carburetor off an old air cooled VW and one of the fuel pump linkage rods is quite worn. It,s just...
10 comments posted 18yrs
posted by susan48
10 comments posted 18yrs posted by susan48

Small welding blanket

I would like to buy a small welding blanket (maybe 5x5 or so). The purpose of it would be shielding flammable stuff fro...
9 comments posted 18yrs
posted by ignoramus23257
9 comments posted 18yrs posted by ignoramus23257

Old Merit Spot Welder

A friend has a Merit spot welder. Serial number is 213 It has no model number on the label. Voltage is listed as 210 vo...
0 comments posted 18yrs
posted by davelf11
0 comments posted 18yrs posted by davelf11

Ping: Tin Lizzie

hi Tin The gauge you're looking for is a modified Starrett #22C gauge that's specially built for the place you work. Th...
5 comments posted 18yrs
posted by johnREMOVETHISgullotti
5 comments posted 18yrs posted by johnREMOVETHISgullotti

fillet welding

in fillet welding SAW any thumbs rules are there...
0 comments posted 18yrs
posted by mgkumar29
0 comments posted 18yrs posted by mgkumar29

Catalytic converters

A friend recently had the catalytic converter stolen from the truck she was driving. Checking into this, we found that...
17 comments posted 18yrs
posted by l.lichtman
17 comments posted 18yrs posted by l.lichtman

SAW

what is the W/d ratio for saw welding whether excess penetration is good for fillet welds say ...circumferential fillet...
1 comments posted 18yrs
posted by mgkumar29
1 comments posted 18yrs posted by mgkumar29

Storage shelf welding project completed

The storage shelf project I used as justification to buy a welder is now complete. (and I ended up with a second new we...
17 comments posted 18yrs
posted by curt
17 comments posted 18yrs posted by curt

MIG settings post #2

I previously posted a question about teaching people to set MIG machines (for short-circuiting transfer). I came up wit...
0 comments posted 18yrs
posted by matthewprays
0 comments posted 18yrs posted by matthewprays

? using a pull back ram to correct a weldment

Hi, I have a large weldment where I need to push two of its surfaces togather to get better bolt hole alignment. The su...
8 comments posted 18yrs
posted by zeb7k
8 comments posted 18yrs posted by zeb7k

Dumb question: 6010 rod

Hi! I was taught to use a "whip" or "in-line stitch" motion when welding with 6010 rod. I have noticed that this makes...
5 comments posted 18yrs
posted by matthewprays
5 comments posted 18yrs posted by matthewprays

Fire and gas tanks

What happens if a set full size welding oxygen and acetylene gas tanks were in a fire? Would it explode and level a few...
9 comments posted 18yrs
posted by <Frank>
9 comments posted 18yrs posted by <Frank>

Spot welding using Stick (or TIG) welder

Assuming one has a stick or TIG welder, can these be adopted to do spot welding ? Am thinking about using this to spot...
1 comments posted 18yrs
posted by rashid.karimov
1 comments posted 18yrs posted by rashid.karimov

SA200=California

Lincoln SA200 portable welder on trailer - $800 (Hemet) Reply to: snipped-for-privacy@craigslist.org Date: 2008-08-18,...
1 comments posted 18yrs
posted by gunner
1 comments posted 18yrs posted by gunner

Generator

I need to power my Lincoln SP 175+ in a remote location without bringing in a line off the pole. ($$$) It calls for 220...
22 comments posted 18yrs
posted by toquerville
22 comments posted 18yrs posted by toquerville