⏣ General Metalworking

30777 Threads Posts
to

taking water out of air supply

I've wired in a new 220v, 60 gal. air compressor and am in the processing of plumbing the air lines. At one location I...
13 comments posted 20yrs
posted by a6016
13 comments posted 20yrs posted by a6016

repairing stripped threads with JB Weld

I have stripped out the threads in a 1/4" bolt hole in an aluminum transmission case. I can't get a drill in there to b...
21 comments posted 20yrs
posted by emmo
21 comments posted 20yrs posted by emmo

MAZAK ACE LATHE 16 X 60

I JUST BOUGHT A MAZAK ACE LATHE 16 X 60 AND CAN'T GET THE POWER FEED TO WORK. THE SELECTOR THAT INGAGES FORWARD AND REV...
1 comments posted 20yrs
posted by nlg
1 comments posted 20yrs posted by nlg

sphere making machine plans

I would like to make a sphere machine. Does anyone know where to get some plans? Alternately, any open-ended advise on...
9 comments posted 20yrs
posted by joshwestcoast
9 comments posted 20yrs posted by joshwestcoast

The Three Day Rule

We have been talking of tools we can't find. You know, the one you KNOW you have eight of ........... Well, another sla...
19 comments posted 20yrs
posted by boozoochavez
19 comments posted 20yrs posted by boozoochavez

Gunner situation? (ping)

I know gunner had been under the weather with pneumonia recently, and he's been absent from the board for the past few d...
1 comments posted 20yrs
posted by jim_member
1 comments posted 20yrs posted by jim_member

Dyna Mechtronics Forum

Just a quick note and reminder that there is a new Dyna Mechtronics Forum phpBB style at http://www.professorwiz.com/for...
0 comments posted 20yrs
posted by russw
0 comments posted 20yrs posted by russw

Aluminum tempering for landing gears?

I have messed with radio control models for years and I have worked in machine shops for over 30 years so Im familiar w...
9 comments posted 20yrs
posted by machwon
9 comments posted 20yrs posted by machwon

cutting torch automation - book review

Recently someone said there was a design for an automated flame cutting machine in the book "The racer's guide to fabri...
2 comments posted 20yrs
posted by grant
2 comments posted 20yrs posted by grant

Advice needed on buying a used lathe

I've just begun learning metal turning with the help of a friend, and now I'm in the market for a small to medium sized...
17 comments posted 20yrs
posted by ahw
17 comments posted 20yrs posted by ahw

Carbide Cannons in the Netherlands

Hello all over the world, 31 Dec 2005 is it time for us great Carbide cannon fom 180 Liters. The pipe is 155 cm and 40...
6 comments posted 20yrs
posted by jfdebaron
6 comments posted 20yrs posted by jfdebaron

Machining Tips of a Hook

Hi folks, I'd be grateful if someone advised me on this: We'd like to machine tips of hooks that are used in industrial...
0 comments posted 20yrs
posted by kumar_ramachandra
0 comments posted 20yrs posted by kumar_ramachandra

Motor mount for Burke #4

Might anyone have a motor mount and pivot bracket for a Burke #4, or can anyone suggest where I might find one? Thanks
0 comments posted 20yrs
posted by dannyrbp
0 comments posted 20yrs posted by dannyrbp

Rolling Metals?

Hi folks, I'm starting to build an EV modeled after the Hailfire droid from Star Wars, here's an image: http://www.star...
4 comments posted 20yrs
posted by v12ogy
4 comments posted 20yrs posted by v12ogy

ARgggggggggghhhhhh!

About six to eight times out of ten, when I go looking for a 1/4" or 5/16" nut driver, I can not find one. So, I go buy...
35 comments posted 20yrs
posted by boozoochavez
35 comments posted 20yrs posted by boozoochavez