⏣ General Metalworking

30777 Threads Posts
to

METRIC Rivets

I'm looking for metric 'swell neck' rivets. Yes, there are rivets that are called 'swell neck' rivets. They are round h...
3 comments posted 21yrs
posted by fuhhkyu
3 comments posted 21yrs posted by fuhhkyu

Need help finding half round

We need about 100 feet of 1/4" half round, preferable aluminum. My google searches and suppliers like McMaster Carr hav...
2 comments posted 21yrs
posted by bounce
2 comments posted 21yrs posted by bounce

Q: How to make parts in plastic ?

Do anyone here know a site that explain how to "Make your own plastic parts" ? I am thinking aboat the prosess innvolvi...
5 comments posted 21yrs
posted by nobody
5 comments posted 21yrs posted by nobody

Office chair (metal) repair

I have two identical office chairs. The air-shock in one of the chairs will not hold air. Is this repairable? Do they co...
8 comments posted 21yrs
posted by ivan
8 comments posted 21yrs posted by ivan

How much air is enough?

I have various air tools and they seem to be ok, then I bought a 3" circular metal high speed cutter and my compressor...
12 comments posted 21yrs
posted by foolinyu
12 comments posted 21yrs posted by foolinyu

Question on old Skil saw

I bought an ancient Skil Saw for a few bucks, thinking that I was going to use it with a metal cutting blade to cut ste...
9 comments posted 21yrs
posted by fergusonOMITsculpture
9 comments posted 21yrs posted by fergusonOMITsculpture

OT: More LED Info

Hi all, I know it's off topic, but there has been a lot of LED discussion here lately, and this interesting Slashdot en...
0 comments posted 21yrs
posted by erik
0 comments posted 21yrs posted by erik

Vibratory Tumbler media

I'm looking for a source for relativly inexpensive tumbler media to finish brass & steel parts. Got a tumbler from ebay...
12 comments posted 21yrs
posted by msmith5242
12 comments posted 21yrs posted by msmith5242

Safety question: mill as saw?

Hello all, I will need to mill a roughly 4x4 inch rectangular hole in what amounts to a thin plate (it's actually a tru...
8 comments posted 21yrs
posted by bschwab
8 comments posted 21yrs posted by bschwab

Who wanted the 16" shaper? I found ya a goodie!

Someone in California was wanting a 16" shaper I found ya a really nice GEMCO 16" hydraulic shaper. A bit of surface ru...
3 comments posted 21yrs
posted by gunner
3 comments posted 21yrs posted by gunner

My compressor slowly overpressurizes

I've got a Quincy 325 turned by a gas engine. When it reaches 125 psi the unloader works both the intake valves and the...
9 comments posted 21yrs
posted by ogyver
9 comments posted 21yrs posted by ogyver

need suggestion for surface grinding wheel

Hello, I'm trying to resurface the magnetic chuck on my surface grinder but the grinding wheel I have is too hard to do...
6 comments posted 21yrs
posted by siralbabin
6 comments posted 21yrs posted by siralbabin

Carboloy TG-24096 tool holders

Anyone know a good source for inserts for these? I have 17 of them and I don't need that many so I'm willing to swap so...
0 comments posted 21yrs
posted by tillman.stevens
0 comments posted 21yrs posted by tillman.stevens

Drill Chuck Arbors

Can anyone tell me what these drill chuck arbors are used for? I bought them on ebay thinking they were something else....
11 comments posted 21yrs
posted by tillman.stevens
11 comments posted 21yrs posted by tillman.stevens

FA: Monarch 10ee Lathe Bedways & Base Casting

Hi all, If you have a 10ee with shot ways and you've ever been tempted to do something about it, and especially if you...
0 comments posted 21yrs
posted by jessehmailbox-rcm
0 comments posted 21yrs posted by jessehmailbox-rcm