⏣ General Metalworking

30777 Threads Posts
to

FS-Transformers

I managed to scrounge up three transformers yesterday that might be handy for someone to own. Two of them are of the bu...
0 comments posted 21yrs
posted by gunnerNOSPAM
0 comments posted 21yrs posted by gunnerNOSPAM

Another chuck question

Amongst the tooling that came with a lathe is a small 3-jaw, about 6" diameter. The mounting method on the backplate is...
7 comments posted 21yrs
posted by rex
7 comments posted 21yrs posted by rex

Help - Disassembling Enco QC box

I recently bought an Enco 1024, 1986 vintage, with some QC box "issues". Basically, it's jammed. So I'm disassembling i...
0 comments posted 21yrs
posted by rex
0 comments posted 21yrs posted by rex

What machines would this chuck fit?

I recently picked up an Atlas 12x36 lathe, and with it was a 9" diameter 3 jaw Cushman chuck with a 2 1/4"-8 threaded b...
6 comments posted 21yrs
posted by myName
6 comments posted 21yrs posted by myName

Damn Chuck

When I first started fooling around with metal working 9 years ago, I bought a Jacobs 14N chuck and stuck it on an Enco...
11 comments posted 21yrs
posted by cjdesigns1NOSPAM
11 comments posted 21yrs posted by cjdesigns1NOSPAM

Quiet muffler for lawn tractor

I have an old lawn tractor that I want to make quieter. It has a single cylinder Briggs & Stratton 8hp engine that has...
19 comments posted 21yrs
posted by dbirch
19 comments posted 21yrs posted by dbirch

Magnetic switch

I picked up a table saw(very large cast iron top) 5 hp single ph motor, has a magnetic switch on it . It will run only...
17 comments posted 21yrs
posted by andrewV
17 comments posted 21yrs posted by andrewV

Anyone looking for an excello mill?

I talked to a person today that is selling an excello mill he says its a bit bigger than a Bridgeport, he has 2 other i...
4 comments posted 21yrs
posted by wayneCLEARTHISTYPE
4 comments posted 21yrs posted by wayneCLEARTHISTYPE

OT: looking for full size van

My deal for a '99 Ford E-350 12 pas. extended body fell through and I am once again looking for a van. I'm in Ohio but I...
0 comments posted 21yrs
posted by tom(nospam)
0 comments posted 21yrs posted by tom(nospam)

Should I kick myself?

A guy showed up at the shop door today with a pick-up load of new equipment to sell. It probably wasn't a scam as the t...
26 comments posted 21yrs
posted by kmiller
26 comments posted 21yrs posted by kmiller

Lathe Upgrade

I'm looking for input on a couple of lathes that I'm interested in.The first is an English Myford which I'm going to lo...
2 comments posted 21yrs
posted by steve
2 comments posted 21yrs posted by steve

Source for 3" thick HDPE sheet or bar?

Ok, so HDPE is not exactly metal. But it's for a metalworking project... I need some 3" thick HDPE, specifically: 16.5"...
4 comments posted 21yrs
posted by no-spam
4 comments posted 21yrs posted by no-spam

tesla turbine #4

I actually used the lathe and the mill on this one. hard drive disks and bearings (actually, the whole thing spins on t...
4 comments posted 21yrs
posted by aiiadict
4 comments posted 21yrs posted by aiiadict

Pole Barn

Thinking of building a pole barn shop about 24x32. Have to do by myself. has to have gravel as I am on a limited budget...
21 comments posted 21yrs
posted by stryped
21 comments posted 21yrs posted by stryped