⏣ General Metalworking

30777 Threads Posts
to

Propane engine question

I picked up a wisconsin 2 cylinder engine today its a propane engine, how do you connect the propane. the motor is a Wi...
13 comments posted 21yrs
posted by wayneCLEARTHISTYPE
13 comments posted 21yrs posted by wayneCLEARTHISTYPE

Chemicals

Craig, there are a couple of ebay sources: http://search.ebay.co.uk/_W0QQsassZjarmondbrinkley http://search.ebay.co.uk/...
1 comments posted 21yrs
posted by charadam
1 comments posted 21yrs posted by charadam

drill bit sharpening

I have one of those entry level drill doctors. SOmetimes, when I sharpen large bits, the bit comes out with the point g...
23 comments posted 21yrs
posted by stryped
23 comments posted 21yrs posted by stryped

Fluorescent shop lites: HD strikes again

Awl-- Some time ago on rcm, the subject of fluorescent lighting came up, and I gushy-gushed about the great $7.99 deal...
19 comments posted 21yrs
posted by physical
19 comments posted 21yrs posted by physical

U joint problem

Hey, Started putting a new u joint into that yoke and shaft and ran into a proplem. I got one "cup" in but when I tried...
13 comments posted 21yrs
posted by stryped
13 comments posted 21yrs posted by stryped

Good deal on a floor jack

I found myself needing a hydraulic floor jack to complete some work, so I went browsing the local automotive shops via...
1 comments posted 21yrs
posted by dans
1 comments posted 21yrs posted by dans

Chemical Suppliers in the UK

Hi I need to get hold of some chemicals to create colour some copper sheet. The chemicals I need are such formulas as f...
4 comments posted 21yrs
posted by wolfuk
4 comments posted 21yrs posted by wolfuk

What is it? LIX

Just posted a new set: http://puzzlephotos.blogspot.com/
18 comments posted 21yrs
posted by rhvp67
18 comments posted 21yrs posted by rhvp67

dspic30f6003 processor

sir/madam I have a motor control board fo dspic30f6003 processor.I want to get more details about the processor .This is...
2 comments posted 21yrs
posted by anilmanual
2 comments posted 21yrs posted by anilmanual

Smoking good deal on a floor jack

I found myself needing a hydraulic floor jack to complete some work, so I went browsing the local automotive shops via...
0 comments posted 21yrs
posted by dans
0 comments posted 21yrs posted by dans

Lift pallet rack by hand ?

Do you think it is possible for one average sized adult to lift a 14' upright (ie. the side portion) of a pallet rack....
7 comments posted 21yrs
posted by no
7 comments posted 21yrs posted by no

Skill saw for thick steel?

I just got frustrated trying to use my 14" Milwaukee abrasive cutoff saw to cut a 45 degree angle on 1 inch by 1 inch s...
8 comments posted 21yrs
posted by fergusonOMITsculpture
8 comments posted 21yrs posted by fergusonOMITsculpture

Arc Welder Problems?

I have an old Sears Craftsman 30-230 Dual Range arc welder that I have had for over 20 years. It has had pretty light u...
5 comments posted 21yrs
posted by randallX
5 comments posted 21yrs posted by randallX

STARTING A MACHINE SHOP

HELLO OUT THERE IN DIGITAL LAND. IM A MACHINIST/TOOL AND DIE MAKER OF 10 YEARS AND HAVE DECIDED TO START MY OWN SHOP IN...
22 comments posted 21yrs
posted by ADMIN
22 comments posted 21yrs posted by ADMIN