⏣ General Metalworking

30778 Threads Posts
to

New metalcraft magazine

Hello all I found this new magazine on the stands here in Canada today at Indigo books. It apears to mainly aimed at th...
0 comments posted 21yrs
posted by machineman
0 comments posted 21yrs posted by machineman

Electric Stove disassembly

I've got an electric range that needs some work. The electrical aspects of the job I can manage, it's getting at the in...
1 comments posted 21yrs
posted by nodamned
1 comments posted 21yrs posted by nodamned

surface grinders

Is their a consensus out there regarding small surface grinders? I may be moving in that direction when I get back on m...
9 comments posted 21yrs
posted by deichles
9 comments posted 21yrs posted by deichles

Ping DoN

I've been trying to get through for several days but keep getting "Error 554: Relay Access Denied". Wayne Cook Shamrock,...
20 comments posted 21yrs
posted by wcnews
20 comments posted 21yrs posted by wcnews

Metalcutting tool info sought

Hi, I'm looking for information on the design, manufacture and costing of metal cutting tool inserts. If anyone could a...
1 comments posted 21yrs
posted by c_finlayson
1 comments posted 21yrs posted by c_finlayson

Need help with Southbend Lathe Collet Attachment

I badly need help getting a 6-K handlever-type collet attachment back into operation on a Southbend (SB) 10-K lathe. If...
2 comments posted 21yrs
posted by xantherx
2 comments posted 21yrs posted by xantherx

Stripped Spindle Thread Help

I have a 1979 Chev K10 with front wheel locking hubs. The locknut and spindle thread (at the outer edge) has been parti...
9 comments posted 21yrs
posted by toncat
9 comments posted 21yrs posted by toncat

Unbalanced Phase Converters and Power Loss

I use a 7.5HP rotary phase converter to run my 2HP Sheldon Lathe. I was taking a medium cut in some 1020 steel in backg...
4 comments posted 21yrs
posted by Sierevello
4 comments posted 21yrs posted by Sierevello

Sheldon tailstock problems

I have a similar problem as mentioned in an earlier post. The nib the that sticks up into the bore of my tailstock and...
2 comments posted 21yrs
posted by gmasterman
2 comments posted 21yrs posted by gmasterman

Removing Timken Tapered Bearing From Spindle

I have a Sheldon WM56P lathe and have to remove the spindle for maintenance. It has 2 Timken tapered bearings and when...
3 comments posted 21yrs
posted by Sierevello
3 comments posted 21yrs posted by Sierevello

Stryco blade welder

I delivered a pair of minty Simpson 260-8 voms to a friend who owns a welding machine repair company Wed. (ARCO, Santa...
19 comments posted 21yrs
posted by gunner
19 comments posted 21yrs posted by gunner

Heat treating aluminum?

Hi, New to this group and figured I would post a question. Wondering if there are any metallurgist's on this group, or...
4 comments posted 21yrs
posted by roseauace
4 comments posted 21yrs posted by roseauace

out of position vertical mill

I've got a question (or a few) for the experienced machinists who generously contribute so much to this group. At my sc...
12 comments posted 21yrs
posted by rfm_surveyor
12 comments posted 21yrs posted by rfm_surveyor

Drilling oblique holes in sheet stock

Greetings, I'm starting a project to make some moulding planes from scratch. A hollow plane requires an oval cutting ed...
4 comments posted 21yrs
posted by nospam
4 comments posted 21yrs posted by nospam

Spot welding brass

In full compliance with Murphy's Law I just tried to unscrew a brass (might be bronze - how do you tell?) shaft from a...
9 comments posted 21yrs
posted by none
9 comments posted 21yrs posted by none