⏣ General Metalworking

30778 Threads Posts
to

OT Things to do before the inauguration

Some Things to Do Before the Inauguration. 1. Get that abortion you've always wanted. 2. Drink your last clean glass of...
7 comments posted 21yrs
posted by bamboo
7 comments posted 21yrs posted by bamboo

Workbench Tops

The Wife asked what I would like to have for my shop this Christmas and I mentioned stainless steel overlays for the tw...
10 comments posted 21yrs
posted by stevemonroe
10 comments posted 21yrs posted by stevemonroe

Daytona Mig Pocket Pulse TIG welder opinions?

I posted this on the welding newsgroup but got no response. Given that it is a DC only 110v box, is the Daytona Mig Poc...
1 comments posted 21yrs
posted by emmo
1 comments posted 21yrs posted by emmo

ANOTHER Onan DJE generator starting problem! (Sunday)

Something strange happened today. My onan generator started, ran for like 2 seconds, and shut down, Then it just would...
8 comments posted 21yrs
posted by ignoramus19295
8 comments posted 21yrs posted by ignoramus19295

FA: Live Steam Loco Parts on eBay

Hello all: I bought some parts for a live steam loco off a friend a while back - no drawings, docs, etc. He got them at...
0 comments posted 21yrs
posted by wallyblackburn
0 comments posted 21yrs posted by wallyblackburn

OT: Coffee grounds down the sink drain?

Anyone got some imput about putting coffee grounds down the sink drain. Are they acidic enough to do good or do they clo...
14 comments posted 21yrs
posted by shakascaregiver
14 comments posted 21yrs posted by shakascaregiver

Call for Ignoramus7135

Hi; Have watched your progress with Onan diesel with interest, drop me an email with your e address and I hope I can sup...
0 comments posted 21yrs
posted by atrei
0 comments posted 21yrs posted by atrei

OT: WTD HP Design Jet 330

Looking for a good used 24"+ Plotter. Prefer an old Designjet 330 but might listen to others. Prefer AZ area or West Coa...
0 comments posted 21yrs
posted by escarcegaNOSPAM
0 comments posted 21yrs posted by escarcegaNOSPAM

Compressor Question

Hi, not really related to the topic, but thought someone should have some knowledge on the subject. I have a compressor...
6 comments posted 21yrs
posted by steve_cornick
6 comments posted 21yrs posted by steve_cornick

The Things You Think of Lying In Bed

Okay. Assuming I wanted a small heat treating oven to handle tempering small tools which had been previously hardened w...
3 comments posted 21yrs
posted by rcook5
3 comments posted 21yrs posted by rcook5

Ignition coil

My forklift has the older, cylindrical shaped ignition coil, with a 12 volt system. The coil was using an external resi...
16 comments posted 21yrs
posted by occupantr
16 comments posted 21yrs posted by occupantr

Homebrew PTC heated diesel fuel filter ?

I am trying to make a budget heater setup to heat the filter separator on my old truck and use a dieslel + VO mix ( I w...
3 comments posted 21yrs
posted by rkpatt758
3 comments posted 21yrs posted by rkpatt758

What is this generator component? Rheostat?

Thanks to all for your previous suggestions, which enabled me to run the generator. I have a question. There is a part...
19 comments posted 21yrs
posted by ignoramus7135
19 comments posted 21yrs posted by ignoramus7135

The Stuff from hell :-)

Got a job in our shop right now that I wish would go away. Putting a 2-3/4" hole 8" deep through a block of 718 Inconel...
5 comments posted 21yrs
posted by machineman
5 comments posted 21yrs posted by machineman

FS: 20 HP ABB inverter

Nice unit 20 HP ABB VFI 208-460 VAC tom
1 comments posted 21yrs
posted by invntrr
1 comments posted 21yrs posted by invntrr