⏣ General Metalworking

30778 Threads Posts
to

neat metal sign I saw

Saw this in Courtney BC, Canada. http://www.rhgrafix.com/Hamilton_logging1_sm.jpg R. Hamm -=(RH)=- ²°°³ http://w w w . r...
0 comments posted 22yrs
posted by emailtogrouponly
0 comments posted 22yrs posted by emailtogrouponly

Which Stainless Grade is easiest to machine?

I will be turning and milling some stainless steel bar for my motocycle. Pieces are decorative only - strength not impo...
14 comments posted 22yrs
posted by eferg
14 comments posted 22yrs posted by eferg

OT: Thinking of moving to Phoenix (was LasVegas)

I mentioned a couple things to the owner like getting material for our products and heat treating. There are no sources...
9 comments posted 22yrs
posted by mpi-brwNADA
9 comments posted 22yrs posted by mpi-brwNADA

A9 bolt

Does anyone out there know of a source for A9 grade bolts? A customer has asked me to source this but the closest thing...
5 comments posted 22yrs
posted by irononeart
5 comments posted 22yrs posted by irononeart

Magazines used to be good

Perusing the exchange area at the local recycling facility (dump), I came across a whole box of Popular Science, Pop Me...
21 comments posted 22yrs
posted by erich10983
21 comments posted 22yrs posted by erich10983

Arc welder and house lights/appliances

Hello all! Finally considering an arc welder. I still must decide between buying/building either a transformer type or...
23 comments posted 22yrs
posted by cramos
23 comments posted 22yrs posted by cramos

FS or Trade:Stainless Art (Buckles)

Taking offers or trade for electronics: scanners,cb,ham radios,etc. and so on ALL ONE OF A KIND also does anybody else...
2 comments posted 22yrs
posted by tommyboys_news
2 comments posted 22yrs posted by tommyboys_news

Awning Work Needed

I need some canvas work done. Does anyone here do this? I need some Sunbrella cut and sewn into flat panels with gromme...
0 comments posted 22yrs
posted by deserttraveler
0 comments posted 22yrs posted by deserttraveler

Evolution cut off saw

Another cut-off saw question. I ran across the Evolution "cold" cutoff saw on the web. Does anyone have any experience/...
5 comments posted 22yrs
posted by no
5 comments posted 22yrs posted by no

Rope Seals

Lookin for some advise replaceing a rope seal on a 40s vintage air compressor. Shaft dia is 1.375" and outside dia of r...
7 comments posted 22yrs
posted by W_E_Coyote_SG
7 comments posted 22yrs posted by W_E_Coyote_SG

Aloris vs KDK- Neil was right

My apologies to Neil Gitter, National Sales Manager for Phase2. Those triangular insert holders I was critical of were...
0 comments posted 22yrs
posted by tomcas
0 comments posted 22yrs posted by tomcas

Yale Electric Chain Hoist Question

Hi, First a warning, then a question. I recently got ripped off by an ebay seller going by the name unclemonkeygocom. I...
2 comments posted 22yrs
posted by mptoolman
2 comments posted 22yrs posted by mptoolman

Adding a run capacitor

I have a 1/2 HP pump motor (dayton, capacitor start) that I would like to add a run capacitor to. The motor is drawing...
14 comments posted 22yrs
posted by cherrybarb
14 comments posted 22yrs posted by cherrybarb

Keller die filer value?

How much is a small Keller die filer, complete, turnkey, with a few files, no V-jaw (plain flat jaws) to hold files, loc...
2 comments posted 22yrs
posted by grantNOSPAM
2 comments posted 22yrs posted by grantNOSPAM