⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30748 Threads Posts
to

That moment

... that moment when you look up at the monitor BEFORE you realize its a spider walking on the lens of the surveillance...
0 comments posted 2yrs
posted by none
0 comments posted 2yrs posted by none

oil-can for toolbox for air-tool oil

Hello all Ideas for smallish oil-can which can be in a toolbox? - mustn't leak all over - smallish and light - can deli...
10 comments posted 2yrs
posted by null
10 comments posted 2yrs posted by null

Geometric Self Opening Die Heads

Geometric Self Opening Die Heads I've made simple die heads. Some driven by a tommy bar, others by a pin in the mandrel...
12 comments posted 2yrs
posted by none
12 comments posted 2yrs posted by none

chainsaw cylinder temperature?

I've been using my late 90's Husqvarna 350 to cut slabs from a large log, to fit it into my sawmill. It's a high end ho...
5 comments posted 2yrs
posted by muratlanne
5 comments posted 2yrs posted by muratlanne

Thunderbird setting change

And I need to type in at least a few lines to see if the line wrap is now going to do what I wish it had been doing for...
6 comments posted 2yrs
posted by Snag_one
6 comments posted 2yrs posted by Snag_one

Inside micrometer

I scored an older unit complete with all the rods ...but they are not set correctly . The 1.5-2.5" is off by about .009...
4 comments posted 2yrs
posted by Snag_one
4 comments posted 2yrs posted by Snag_one

Dirty Hands Clean Money

Converted an R8 tool rack into a 4MT tool rack. First ten seconds and last minute is probably all you need to see to ge...
7 comments posted 2yrs
posted by none
7 comments posted 2yrs posted by none

I Quit

I'm sure you are all tired of the saga of the built to "a" spec Ingersol Rand compressor from Craptor Supply. The one t...
28 comments posted 2yrs
posted by none
28 comments posted 2yrs posted by none

Another tool ...

A Scherr-Tumico inside micrometer this time . Looks like one of the rods might be missing , hope it's not the one I need...
2 comments posted 2yrs
posted by Snag_one
2 comments posted 2yrs posted by Snag_one

Auction Metal Stuff

Hey Bob and others, Thought I would share a bit of humor!! Especially Lot's 46 - 47 - 48!!...
0 comments posted 2yrs
posted by somebody
0 comments posted 2yrs posted by somebody

Make it fit ...

I've cut 2 of the depth mike rods so far , easier than I thought it would be to adjust them . I'm getting them close ri...
4 comments posted 2yrs
posted by Snag_one
4 comments posted 2yrs posted by Snag_one

Gauge blocks arrived

Actually yesterday afternoon . A really nice wood case , each block is serialized and has the chart of variances . Not t...
8 comments posted 2yrs
posted by Snag_one
8 comments posted 2yrs posted by Snag_one

Gauge blocks

Am I really going to need to allow for millionths of an inch ? I'm looking at an 81 piece set from Shars , a grade B wi...
11 comments posted 2yrs
posted by Snag_one
11 comments posted 2yrs posted by Snag_one

Depth mike

I scored a Mitutoyo unit a while back at a yard sale . It only had one rod , 0-1" and I wanted more ... so I bought som...
10 comments posted 2yrs
posted by Snag_one
10 comments posted 2yrs posted by Snag_one