⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

UK Auction Sites

Hello there, I occasionally sell engineering bits and bobs on E Bay but now that they've put there prices up and they d...
2 comments posted 18yrs
posted by Nourish.3en80n
2 comments posted 18yrs posted by Nourish.3en80n

Equipment stolen from near Warrington

Some evil scrote has taken one of these from my premises http://cgi.ebay.co.uk/JANCY-MAGNETIC-DRILL-MAG-DRILL-4-X-4-THE...
0 comments posted 18yrs
posted by duttondock
0 comments posted 18yrs posted by duttondock

FS: Ajax AJMD30 mill

Unused, on stand. £900 or will swap for small precision mill (sherline or any half decent table-top mill) Buyer will ne...
3 comments posted 18yrs
posted by odie_ferrous
3 comments posted 18yrs posted by odie_ferrous

Need Info Myford Rotary Switch box pre-1980

I am looking for two Myford switches. I am not sure of the exact type, model No. or year. It is a A.C Only, 5 amp switc...
0 comments posted 18yrs
posted by seventhz777z.3egcsn
0 comments posted 18yrs posted by seventhz777z.3egcsn

Shopping stuff

I recently did some shopping at www.technobots.co.uk - ordered a lot of mixed small parts on Sunday, got an email Monda...
41 comments posted 18yrs
posted by zenadsl6186
41 comments posted 18yrs posted by zenadsl6186

grub screw

Hi, After six succesful ones, I did it again... What is the way to remove a M2x4 unslitted grub screw from a locked up b...
6 comments posted 18yrs
posted by df.ganzinga
6 comments posted 18yrs posted by df.ganzinga

Telescopic bore micrometer?

This is something that has intrigued me for a while, as I'm sure I used them at college for measuring engine cylinder b...
6 comments posted 18yrs
posted by mtbhypenrules
6 comments posted 18yrs posted by mtbhypenrules

Taper Mandrels and accuracy

I have dusted off the Stuart 10V castings, dug out the building book and found Issue 51 of MEW. Time to get started aft...
11 comments posted 18yrs
posted by peter.harrison
11 comments posted 18yrs posted by peter.harrison

motor starting and reversing.

I bet this appears twice now. it seems to be in limbo, so reposting... got cheap on ebay a box with forward reverse sto...
49 comments posted 18yrs
posted by austinDITCHTHISFORBETTERRESULT
49 comments posted 18yrs posted by austinDITCHTHISFORBETTERRESULT

Progress 1S Pillar Drill – Jacobs 34 Chuck

Our club workshop pillar drill really needs a new chuck. We?ve got a keyless jobby in mind but need to get the existing...
8 comments posted 18yrs
posted by postmaster
8 comments posted 18yrs posted by postmaster

motor starting and reversing.

got cheap on ebay a box with forward reverse stop buttons, but that's all it is, the box and contactors under the butto...
7 comments posted 18yrs
posted by austinDITCHTHISFORBETTERRESULT
7 comments posted 18yrs posted by austinDITCHTHISFORBETTERRESULT

Turning a small diameter?

Evening all, I have a need to turn a number of components (probably in aluminium or brass, it depends what's lying arou...
5 comments posted 18yrs
posted by nigele
5 comments posted 18yrs posted by nigele

Angle Grinder Question

Hi, Hoping someone with some sense can help. I've being having problems for a long while now with 4 1/2" and 9" angle g...
2 comments posted 18yrs
posted by MERLIN_IN_UK
2 comments posted 18yrs posted by MERLIN_IN_UK

Angle Grinder Question

Hi, Hoping someone with some sense can help. I've being having problems for a long while now with 4 1/2" and 9" angle g...
9 comments posted 18yrs
posted by MERLIN_IN_UK
9 comments posted 18yrs posted by MERLIN_IN_UK