⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Bevel Gears

. Can any kind soul point me towards a source of ready made bevel gears please? Seeking a couple of sets 14:41 with the...
2 comments posted 19yrs
posted by Mike
2 comments posted 19yrs posted by Mike

Aligning the tailstock?

Hello again, Basic question no 537 from me: I'm about to start my first 'real' machining job. It is basicall drilling o...
31 comments posted 19yrs
posted by DR_G.2ze2kn
31 comments posted 19yrs posted by DR_G.2ze2kn

Steel and diamond

I have to grind some steel using a diamond tool. Any tips on extending tool life? Thanks, -- Peter Fairbrother
5 comments posted 19yrs
posted by zenadsl6186
5 comments posted 19yrs posted by zenadsl6186

Chocolate Coated Sprouts

Heard that one on the radio today. Thought it was a particularly good idea as 'treats' to dish out to the little bugger...
4 comments posted 19yrs
posted by panuno95-ukrec
4 comments posted 19yrs posted by panuno95-ukrec

Chronos kit.

Just taken delivery of one of the Shoba 6 inch rotary table kits, with the extras, indexer, centre, etc etc, and a few...
9 comments posted 19yrs
posted by davenull
9 comments posted 19yrs posted by davenull

Gingery videos

Found some interesting video clips here of Gingery's machines: http://www.gingerybooks.com/ Regards, Tony
0 comments posted 19yrs
posted by tony
0 comments posted 19yrs posted by tony

Oil cans

Why do pump action oil cans leak? I have two that both mysteriously accumulate oil over the outside and onto the shelf...
11 comments posted 19yrs
posted by clifford.coggin
11 comments posted 19yrs posted by clifford.coggin

SERT Gone?

I hadn't been to the shop for a while, but popped down on Saturday to look for a small Jacobs chuck on a 2MT shank, to...
7 comments posted 19yrs
posted by Jim Guthrie
7 comments posted 19yrs posted by Jim Guthrie

Anyone got a surplus 2" bore hydraulic ram?

Hi all, Does anyone have an unwanted 2" bore hydraulic ram? Preferably as long as possible. It's okay if the seals leak...
16 comments posted 19yrs
posted by cdt22NOSPAM
16 comments posted 19yrs posted by cdt22NOSPAM

It went for how much..????

These Delapena thingies always go for a fortune: DELAPENA/MYFORD LATHE PORTABLE PRECISION HONING TOOLS CONTROL HEADS, H...
1 comments posted 19yrs
posted by Myford.Matt.2z8d0n
1 comments posted 19yrs posted by Myford.Matt.2z8d0n

Compressor Workings

I have a compressor that does not have an automatic cut-off switch, I either let the safety valve blow or keep turning...
5 comments posted 19yrs
posted by mailveil13-usenet
5 comments posted 19yrs posted by mailveil13-usenet

Lathe overhead gear

Do people still use overhead gear on lathes for driving cutters on the cross slide, or have small electric motors made...
9 comments posted 19yrs
posted by alanb+news
9 comments posted 19yrs posted by alanb+news

US thread taps

Does anyone know where I might buy a 5/8-20UN tap? A spiral point would be great, but any port in a storm! Steve (Sheffi...
12 comments posted 19yrs
posted by steveaddyatdsl.pipex.com
12 comments posted 19yrs posted by steveaddyatdsl.pipex.com

Bridgeport Quill Return Springs

Something of a blatant plug I'm afraid.... A couple of weeks back someone was asking how to get a Quill Return Spring f...
1 comments posted 19yrs
posted by ieb
1 comments posted 19yrs posted by ieb

Myford Factory Visit Today.

Hello yet again, (yes, two posts in one evening!) I went to the Myford Factory open day this afternoon - it was reall g...
22 comments posted 19yrs
posted by DR_G.2z16on
22 comments posted 19yrs posted by DR_G.2z16on