⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

ML7 Collets & General Update on Lack of Progress.

Hello again Folks, You will all no doubt not be at all surprised that I haven't ye started on a 'proper' machining proj...
37 comments posted 19yrs
posted by DR_G.2z13wn
37 comments posted 19yrs posted by DR_G.2z13wn

Source for small 0.25hp motors

I have a lorch lathe that has a 3 phase motor on that I want to run o an inverter. As the star point is in the motor do...
3 comments posted 19yrs
posted by Steve.Larner.2z0q0o
3 comments posted 19yrs posted by Steve.Larner.2z0q0o

Megga readings on a motor

I have just aquired an old geared head drill press. The motor has wires so I have cut the star point off and paired the...
4 comments posted 19yrs
posted by Steve.Larner.2z0q0n
4 comments posted 19yrs posted by Steve.Larner.2z0q0n

RPM reading

Hi, is anyone out there who can give a me some advise about a (simple) device to read the spindle speed of my S7 , drive...
14 comments posted 19yrs
posted by j.roos12
14 comments posted 19yrs posted by j.roos12

Indicator plug

I often forget to turn off my electric soldering iron when I leave the workshop. Quite apart from the waste of power I...
12 comments posted 19yrs
posted by clifford.coggin
12 comments posted 19yrs posted by clifford.coggin

Acme screws

Hi all. I am looking for a supplier of budget priced Acme/ Trapezoidal style ball screws up to 2 metres in length in the...
3 comments posted 19yrs
posted by rjisnik
3 comments posted 19yrs posted by rjisnik

Worst paint job

Have at look at this, must hurt your eyes if using it for long periods Ebay Item number: 160171374467 (don't worry AWEM...
7 comments posted 19yrs
posted by emimec
7 comments posted 19yrs posted by emimec

Questions about 23 inch standard racks

I need to design a 23 inch standard cabinet. But I don't know which standard should the rack follows. Someone tell me i...
1 comments posted 19yrs
posted by lelele
1 comments posted 19yrs posted by lelele

Drills for 316?

I need to drill 2.5mm dia. holes 20mm deep in 316 stainless steel. Will ordinary HSS drills be okay, or is there a bette...
3 comments posted 19yrs
posted by jimhawkins
3 comments posted 19yrs posted by jimhawkins

Non Urgent Transport panic

morning all, Slightly OT, but it is metal Im shipping... Its not as urgent as Andrews was, but I need to ship a crate t...
4 comments posted 19yrs
posted by david.sanderson
4 comments posted 19yrs posted by david.sanderson

Soft centres...

Ok, let's start off by admitting that I'm not in the best of moods:- 1) The "heavy duty" Hilti breaker that I hired thi...
17 comments posted 19yrs
posted by randm
17 comments posted 19yrs posted by randm

30 hp 3 phase motor

I have a large 3 phase 22kw electric motor which I cannot use in my single phase or 3kw 3 phase workshop. Does anyone k...
0 comments posted 19yrs
posted by georgewbell
0 comments posted 19yrs posted by georgewbell

IME Watchmakers lathe eBay item 250178741171

Hi Chaps, I'm auctioning my IME 8mm watchmakers lathe on eBay. The item number is 250178741171 and I've attached the au...
2 comments posted 19yrs
posted by mikedavies621
2 comments posted 19yrs posted by mikedavies621

Urgent Transport Panic!!!

Does anyone have phone numbers for a private operator machine shifter based SE London or East Sussex equipped with a hi...
26 comments posted 19yrs
posted by andrew
26 comments posted 19yrs posted by andrew

Oilite bushes

Having carefully installed new Oilite bushes in the apron of my Myford ML7 lathe, I belatedly wonder if I should have i...
2 comments posted 19yrs
posted by clifford.coggin
2 comments posted 19yrs posted by clifford.coggin