⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Bridgeport series 1 with Heidenhain DRO

When switching from metric to imperial, all that happens is the decimal point moves over 1. Movement of a slide is stil...
20 comments posted 19yrs
posted by emimec
20 comments posted 19yrs posted by emimec

ebay page width

Is it just me, or has ebay changed its page width slightly in the last few days. If I look at any specific item it is e...
2 comments posted 19yrs
posted by andrew
2 comments posted 19yrs posted by andrew

Chris Heapys web site

Is there still a copy of Chris's web site about if so anyone know the address Thanks
3 comments posted 19yrs
posted by andrew
3 comments posted 19yrs posted by andrew

Magnetic chuck

Just bought a magnetic chuck for a small surface grinder, it's i overall good order but some idiot has at some time low...
5 comments posted 19yrs
posted by stereotype.2ikegb
5 comments posted 19yrs posted by stereotype.2ikegb

Ward Capstan 3db

nice buy if it stays this low loads of tooling usual disclaimer just thought it might interest someone http://www.henryb...
2 comments posted 19yrs
posted by andrew
2 comments posted 19yrs posted by andrew

Boilermaking

Anybody point me to chapter and verse on the 'new boiler regs'?, since I don't know what the old ones were it might be a...
13 comments posted 19yrs
posted by agatehouse
13 comments posted 19yrs posted by agatehouse

Garagwe clear out - Motors

I am having a clear out. I have 1 x new unused DC motor, 48v, flange mounting. It was designed as a reel motor for high...
1 comments posted 19yrs
posted by brightside
1 comments posted 19yrs posted by brightside

Suds Pump

Anyone know of a source for a cheap and cheerful Suds Pump? tia
13 comments posted 19yrs
posted by sandy
13 comments posted 19yrs posted by sandy

MEW

Is it just me or does anybody else think the latest MEW is a rip-off? As an enclosure with a mag maybe but to pay for w...
78 comments posted 19yrs
posted by andy
78 comments posted 19yrs posted by andy

Velocette Clutch Springs

Hi Group This is a long shot but can anyone give me the sizes of the old Velocette motor cycle clutch springs. If we hav...
6 comments posted 19yrs
posted by me
6 comments posted 19yrs posted by me

Myford lever-operated tailstock

Can anyone supply me with linkage dimensions and maybe a photo of a lever-operated tailstock for an ML7? Somehow I doub...
15 comments posted 19yrs
posted by guy
15 comments posted 19yrs posted by guy

Workshop Floors

I want to re-surface my garage (workshop) floor whilst I have everything moved out of it to clean up after the recent f...
10 comments posted 19yrs
posted by panuno95-ukrec
10 comments posted 19yrs posted by panuno95-ukrec

Benchtop Injection Moulder E-bay

Can't remember who was after something like this, but there is a very basic benchtop moulder on e-bay, item no. 22005803...
1 comments posted 19yrs
posted by panuno95-ukrec
1 comments posted 19yrs posted by panuno95-ukrec

V-4

i am trying to find drawings for a v-4 steam engine designed and buil by peter arnot and published in a model boats mag...
0 comments posted 19yrs
posted by bolmas.2ifxcb
0 comments posted 19yrs posted by bolmas.2ifxcb

cutting gears (myfords)

I need to cut quite a few gears of 1.25 module now I understand that myford 7 gears are 20 dp which = 1.27 module would...
3 comments posted 19yrs
posted by andrew
3 comments posted 19yrs posted by andrew