PRO/Engineer (Creo) discussions

Concrete Forming

I do alot of concrete forming using the Symons Steel-Ply system. Basically I draw a wall (usually 8" wide) in plan view...

1 comments posted 20yrs

posted by cwbrodie

1 comments posted 20yrs posted by cwbrodie

Suppressed objects

I woud like to see suppressed objects when I open a file in WF2. What option is responsible for that in config.pro file?...

3 comments posted 20yrs

posted by ziomall666

3 comments posted 20yrs posted by ziomall666

Duplicating a part

Hello, I have 2 parts that are very similar with different part numbers. I created the 1st part and I need to save time...

7 comments posted 20yrs

posted by COM

7 comments posted 20yrs posted by COM

Points Coordinate export

Hi people. I use WF2. I have a model with some points (it's not a CMM file, it's a "normal" part) and I need to get a f...

3 comments posted 20yrs

posted by pdiletti

3 comments posted 20yrs posted by pdiletti

Intralink 3.2 on a windows server

Hello Everybody, We are planning to migrate our intralink 3.2 installation from a "solaris 2.6" to a "windows server 20...

1 comments posted 20yrs

posted by fretty

1 comments posted 20yrs posted by fretty

'Cannot connect to PTC Name Service. Please ensure that it has been started'

LS, I'm a newbie to Pro-E and would like to know what this message is and how I can solve this. Thanks! JJ

6 comments posted 20yrs

posted by jjzwaard

6 comments posted 20yrs posted by jjzwaard

break out view

Does anyone know how break out view works in WF? I know its under section but somehow its not working can you please giv...

1 comments posted 20yrs

posted by nileshborade

1 comments posted 20yrs posted by nileshborade

Intralink: Created by in WS

I-link gurus: Is there a way to see who worked on a file while in workspace like using the "created by" parameter in co...

7 comments posted 20yrs

posted by pinbuoy

7 comments posted 20yrs posted by pinbuoy

Reflections on good and evil

My name is Lorenzo Crescini and I'm Italian. These "Flashes on Good and evil" reflect the same mood characterizing the...

0 comments posted 20yrs

posted by booktwo

0 comments posted 20yrs posted by booktwo

startup of application edrawings failed

how do you remove this message once you have uninstalled edrawings for proe?

2 comments posted 20yrs

posted by i621148

2 comments posted 20yrs posted by i621148

Sluggish performance when getting close to 2GB w/3GB sw

Does anyone know why PCs running XPPro with 3 GB RAM and the 3 gig switch have sluggish performance when approaching 2G...

2 comments posted 20yrs

posted by pinbuoy

2 comments posted 20yrs posted by pinbuoy

3GB switch on WinXP

How do I tell that this is installed? Is it as simple as "if windows recognizes the 3gb then it's installed" ? Is there...

3 comments posted 20yrs

posted by pinbuoy

3 comments posted 20yrs posted by pinbuoy

recommended paging file size

Hi all, Is there a recommended paging file size? I know the admin at my last job had a recommendation, I just don't rem...

1 comments posted 20yrs

posted by pinbuoy

1 comments posted 20yrs posted by pinbuoy

CADDS 4X, CADDS 5i viewer

DraftView for CADDS® DraftView is a low-cost view, print and markup tool that reads CADDS 4X and CADDS 5 designs direct...

0 comments posted 20yrs

posted by slh

0 comments posted 20yrs posted by slh

Ani

hi all, do you know a way to convert a stl file into a pro/e part file? i could do it using shrikwrap but then if i try...

3 comments posted 20yrs

posted by anirudha.l

3 comments posted 20yrs posted by anirudha.l