⚡ Welding Forums

Digimig wirefeeds?

Hi... Is anyone familiar with "Digimig" wirefeeds? Can they be used, as I suppose, for MIG welding, with a suitable powe...

2 comments posted 20yrs

posted by ignoramus10768

2 comments posted 20yrs posted by ignoramus10768

Carbon Rods for Electric Arc Welder Brazing Attachment

Does anyone know a supplier of carbon rods for Arc Welder Brazing attachments in the UK. I believe these need to be che...

0 comments posted 20yrs

posted by pill

0 comments posted 20yrs posted by pill

How can a person brack old welds to replace materal?

Iv got a trailer that needs a new deck but there is three layers of sheet metal on it now i need to remove the old and...

12 comments posted 20yrs

posted by falcon1643106

12 comments posted 20yrs posted by falcon1643106

TIG electrode contamination question

Hello, I am a novice making great progress with my SS manifold construction thanks to you polymaths here and on RCM gro...

1 comments posted 20yrs

posted by borism

1 comments posted 20yrs posted by borism

Welding on RV frame close to propane bottle

Most of us have welded on automobile frames at one time or and other and while I'm immediately leary the closer I get t...

15 comments posted 20yrs

posted by dvandam

15 comments posted 20yrs posted by dvandam

Aluminum motorcycle cases

I plan to construct a welded aluminum box, custom fitted for a tight spot on a motorcycle, something like http://www.je...

2 comments posted 20yrs

posted by tedbennett

2 comments posted 20yrs posted by tedbennett

Hybrid laser-MIG welding

Can anyone, please, write down some sites where I can find some stuff about hybrid laser-mig welding? Any information wo...

2 comments posted 20yrs

posted by sdsad

2 comments posted 20yrs posted by sdsad

Jackson helmet fan?

I got an Jackson EQC Shadowair ( series1) helmet new on ebay without the fan/belt unit, cheaper than the non-air model....

0 comments posted 20yrs

posted by spam

0 comments posted 20yrs posted by spam

Lincoln SA-200 - How to dismount engine from generator end?

Can anybody clue me in as to how the generator is mated to the rear of the crankshaft? I have a manual for the Continent...

4 comments posted 20yrs

posted by vtuck

4 comments posted 20yrs posted by vtuck

Schedule 40 vs 80 Strength

Hi, I am curious to know what the strength difference of an 8" schedule 80 pipe is over 40. Thanks!

0 comments posted 20yrs

posted by jeff_s_g

0 comments posted 20yrs posted by jeff_s_g

Lincoln short hood SA200

Yesterday I bought another one. This one's a '56 model. The camshaft broke in two while the previous owner was welding...

5 comments posted 20yrs

posted by vtuck

5 comments posted 20yrs posted by vtuck

O/A welding aluminum

I've got a busted (H-D motorcycle) transmission case , cast aluminum . It's busted too bad to repair and use , but will...

16 comments posted 20yrs

posted by snagone

16 comments posted 20yrs posted by snagone

WELDING CABLES IN HOUSTON WANTED

Subject says it all except I will take cable in any condition but the conductor/s must be good.

3 comments posted 20yrs

posted by jbleaux

3 comments posted 20yrs posted by jbleaux

welding shade numbers

Can anyone tell me whether the welding shade scale is linear, or whether it's something else? I was wondering if #3 fla...

5 comments posted 20yrs

posted by vandeweg

5 comments posted 20yrs posted by vandeweg

OT holes through pipe

Where would I find out how you drill a hole straight though a pipe? I guess that a lot of the people in this group would...

6 comments posted 20yrs

posted by pauln

6 comments posted 20yrs posted by pauln