Latest threads in ⏣ General Metalworkingshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Chip formation up close
Slow motion of what happens in the cut. Different coatings, different materials.
—
|
11 years ago
|
— | |
|
|
Making chips - Close up
Regards, Boris Mohar Got Knock? - see: Viatrack Printed Circuit Designs (among other things) _-void-_ in the obvious place
7
|
11 years ago
|
7 | |
|
|
Reducing a 5/8" shaft
Not knowing what "junk" you have available... What about a piece of rubber hose or beverage tubing with a 5/8" id fitted to the sht shaft & held tight with a clamp. Then find something that will fit...
36
|
11 years ago
|
36 | |
|
|
Huge T-slotted table
I am guessing it is 3x12 feet, I have not seen it yet. am wondering, how much do those weigh and are they still used industrially. i http://www.premierarg.com/item.cgi?show_item=0000022218
4
|
11 years ago
|
4 | |
|
|
What options for trailer floor
We just stripped and sandblasted our trailer, it is 20k Cronkhite with a 18 ft long bed. The wood on it was completely rotted and I am now looking for good options. I want this trailer to haul...
13
|
11 years ago
|
13 | |
|
|
Help with 2006 liberty ac
Boy, what a mess! Hard to tell what is wrong. I'm assuming this is an R134a system? The somewhat high pressure on the evaporator could indicate contamination. Did you evacuate the system? How did you...
4
|
11 years ago
|
4 | |
|
|
CNC Bridgeport mill for sale
Picture mill is a lot like my own Bridgeport Interact, except that it is stepper motor powered, and mine is servo motor powered. Steppers are a plus if you want to use Windows based Mach3, otherwise...
32
|
11 years ago
|
32 | |
|
|
How much could this CNC punch press weigh (Wiedematic W-2040)
I bought this at an auction, I wonder what does it weigh. This is a 20 ton CNC punch press.
15
|
11 years ago
|
15 | |
|
|
2-56 push nuts?
I'm looking for a source for 2-56 push nuts. McMaster has let me down.
3
|
11 years ago
|
3 | |
|
|
WORKING PERFECT
Regards Tom. http://lasvegas.craigslist.org/tls/3065340272.html
2
|
11 years ago
|
2 | |
|
|
Hooked up the rattler
That's what she said;-)
1
|
11 years ago
|
1 | |
|
|
McMaster-Carr comes through again!
I ordered on a Thursday some stuff to be shipped next day air from McMaster-Carr. When it didn't arrive by Friday afternoon I checked UPS tracking and the shipping had been changed from next day...
8
|
11 years ago
|
8 | |
|
|
What industrial air quick connects
We have finally hooked up our air compressor to the existing air piping in my factory. The bad news is that the existing connectors are either missing, or old and leaking. I would like to replace them...
22
|
11 years ago
|
22 | |
|
|
Was this bad?
Replaced some Mickey-mouse plastic pipe (by others) on my water utility service connection with a piece of galvanized iron pipe and a flexible "copper water heater connector" hose in place of a proper...
7
|
11 years ago
|
7 | |
|
|
What is it? Set 444
Just posted a new set on the web site: Rob
28
|
11 years ago
|
28 |