⏣ General Metalworking

30777 Threads Posts
to

Tolerance: Hole based vs Shaft based system

Can anyone please tell me why hole based tolerance system is preferred over shaft based tolerance system. thanks
0 comments posted 20yrs
posted by amitsoni.1984
0 comments posted 20yrs posted by amitsoni.1984

Measuring roundness using V-block

Hi! Can anyone please tell me why V-block is preferred to measure roundness of some component. thanks.
9 comments posted 20yrs
posted by amitsoni.1984
9 comments posted 20yrs posted by amitsoni.1984

Small taps and dies

Hi, I am looking for source of small METRIC taps (and dies). Small here means M2.5 and lower. Also looking for source o...
4 comments posted 20yrs
posted by abaldus
4 comments posted 20yrs posted by abaldus

Argon bottle regulator scaling?

My argon bottle regulator is marked in pounds per hour, how do I convert this into liters per timescale, as most info I...
3 comments posted 20yrs
posted by chris
3 comments posted 20yrs posted by chris

Molding knives

I need to make some knives for cutting custom wood moldings. See this for typical profiles: http://www.wmooreprofiles.c...
8 comments posted 20yrs
posted by spamless
8 comments posted 20yrs posted by spamless

Brown & Sharpe Vise

Does anyone know if a Brown & Sharpe No.1 vise was available with a swivel base? If anyone has a base and would like to...
2 comments posted 20yrs
posted by dannyrbp
2 comments posted 20yrs posted by dannyrbp

Making Gears With A Mini-Mill

Can anyone recommend any books that detail how to make bronze or plastic gears and racks specifically on a (mini)Mill,...
0 comments posted 20yrs
posted by Searcher7
0 comments posted 20yrs posted by Searcher7

sheet metal question

Hi I am hoping you gentlemen won't mind answering a newbie question. I want to put a wire rim on a bucket and also do t...
2 comments posted 20yrs
posted by idundidit
2 comments posted 20yrs posted by idundidit

Question

If you gentlemen could help I want to put a wire edge on a bucket rim and also do the bottom seam. I guess you could sa...
1 comments posted 20yrs
posted by idundidit
1 comments posted 20yrs posted by idundidit

TIG inverter -- final gate drive assembly PICTURES

That's for my project of adding a DC -> AC inverter to my DC only welding machine: http://igor.chudov.com/projects/Weld...
4 comments posted 20yrs
posted by ignoramus6826
4 comments posted 20yrs posted by ignoramus6826

wtf: 3c collet lathe

I am interested in a good condition 3c collet lathe - either with or without a turret. I certainly would like to get a...
0 comments posted 20yrs
posted by ghodge7
0 comments posted 20yrs posted by ghodge7

RPC Question

It's been a few years since I've posted, but I have been lurking for most of it. I am resuscitating a B&S 2A universal...
13 comments posted 20yrs
posted by wc***sippola
13 comments posted 20yrs posted by wc***sippola

Ball Bearing Question

I am going to put about 400# on the end of a support that I want to swivel. I figure I am going to use a #8 grade bold...
4 comments posted 20yrs
posted by boozoochavez
4 comments posted 20yrs posted by boozoochavez

Refilling small propane cylinders

Well I suckered for it. Bought the HF brass fitting whereby you can transfer some propane from your barbeque type bottl...
52 comments posted 20yrs
posted by ivan
52 comments posted 20yrs posted by ivan

eBay from another angle

I have been following the thread about "good condition" and "as-is" with great interest. As some of you know, I sell st...
25 comments posted 20yrs
posted by carl.byrns
25 comments posted 20yrs posted by carl.byrns