⏣ General Metalworking

30777 Threads Posts
to

Copper electrodes for electrolytic derusting?

I have certain copper pieces that I could use as electrodes for EDR. I am not sure if that is safe from environmental s...
2 comments posted 20yrs
posted by ignoramus32654
2 comments posted 20yrs posted by ignoramus32654

U-Build Machine & Power Tools Catalo0g

New web catalog features: U-Build Metal Turning lathes & Accessories Milling & Grinding Attachments, Low Cost EDM, Dual...
3 comments posted 20yrs
posted by Poorman.20zpmu
3 comments posted 20yrs posted by Poorman.20zpmu

FS: South Bend 400 lathe

I have a 1986 model south bend lathe for sale15x40 hard ways taper att. quick change toll post & holders coolant new 3...
0 comments posted 20yrs
posted by dannylester
0 comments posted 20yrs posted by dannylester

Homemade Resistance Soldering Unit

I tried posting this earlier, but I got an error message when I went to post it. So, I am not sure the first message we...
28 comments posted 20yrs
posted by onetoncrewcab
28 comments posted 20yrs posted by onetoncrewcab

hard versus soft solder

I'm doing some brass model building and the book that I am using as a guide (by Gerald Wingrove) mentions hard and soft...
23 comments posted 20yrs
posted by onetoncrewcab
23 comments posted 20yrs posted by onetoncrewcab

A metal beam design question

I am looking at designing a metal backhoe boom, looking for strength and minimal weight. Rather than using a structural...
7 comments posted 20yrs
posted by sale_items
7 comments posted 20yrs posted by sale_items

Making A Square Hole In Stainless Steel

Does anyone here have to make square holes on a regular basis? I need to make the 1/4" diameter holes in 1/16" thick st...
31 comments posted 20yrs
posted by Searcher7
31 comments posted 20yrs posted by Searcher7

arc welding with generator

I would like to start practicing with an arc welder on scrap metal so I can move on to welding up metal buildings. The...
11 comments posted 20yrs
posted by ranchersam
11 comments posted 20yrs posted by ranchersam

Beginner's cutoff problems

Metalworkers: I'd like help with cutoff problems. The setup is: An Emco Compact 8 lathe, slowest speed. Candlesticks tu...
12 comments posted 20yrs
posted by dxk10
12 comments posted 20yrs posted by dxk10

Making Square Holes In Stainelsss Steel

Does anyone here have to make square holes on a regular basis? I need to make the 1/4" diameter holes in 1/16" thick st...
0 comments posted 20yrs
posted by Searcher7
0 comments posted 20yrs posted by Searcher7

Anyone need a tube tester?

I scrounged up a B&K "Dyna-Quik Mod. 500 tube tester today. Has the 510 daughter board inside the lid. Case is not bad,...
17 comments posted 20yrs
posted by gunner
17 comments posted 20yrs posted by gunner

Happy New Year

Hi Gunner, Happy New Year, I have enjoyed your posts over the last year, All the best for 2006. Regards Rotty UK
4 comments posted 20yrs
posted by iflyer
4 comments posted 20yrs posted by iflyer

BP Drawbar Shear Pin Question

I couldn't find this info on Google. What is the proper material to use to replace the pin on a Bridgeport drawbar? I tr...
9 comments posted 20yrs
posted by waxwingslain
9 comments posted 20yrs posted by waxwingslain

Armstrong QC Toolposts

Does anyone know if Armstrong QC toolposts/holders are compatible wit the Aloris style dovetail? Armstrong doesn't show...
9 comments posted 20yrs
posted by Joepy.20xuys
9 comments posted 20yrs posted by Joepy.20xuys

Minor page update

--Direct links to changed pages here: http://www.nmpproducts.com/changes.htm --I'd be grateful if any of you lot could...
0 comments posted 20yrs
posted by steamer
0 comments posted 20yrs posted by steamer