3 comments
posted 20yrs
posted by noswal2
⏣ General Metalworking
30777 Threads
Posts
to
Worth reading in ⏣ General Metalworking
- Mitutoyo Digimatic caliper error "Err 05"
- Convert Degrees to Foot Pounds?
- Victor torch tip part number meaning?
- How to open a Mosler safe with combination?
- Lathe Spindle Bore
- Hydraulic power press design
- Steel "U" channel? Or is it "C" channel?
- Does anyone know what thread size a tire valve stem and the Schrader valve are?
- repairing stripped threads with JB Weld
Gate frame
Hi Group, Before I get started, this is my first metalworking project. I'm going to build a gate frame, then clad it wi...
14 comments
posted 20yrs
posted by not
14 comments
posted 20yrs
posted by not
Microscope adapter for digicam
Anybody here made a microscope adapter for a digital camera? I'm thinking of that sort of project for my Canon G3 and a...
14 comments
posted 20yrs
posted by MichaelHenry
14 comments
posted 20yrs
posted by MichaelHenry
Chatter Problem
Hi guys. I'm trying to maching a small item on a lathe. It's going to be a depth gauge, folloeing the directions givien...
8 comments
posted 20yrs
posted by kellytjones
8 comments
posted 20yrs
posted by kellytjones
Why Are Stainless Steel Chips Bad?
In reading the Novermber/December 2005 issue of "The Home Shop Machinist", the author of the article on building a hori...
9 comments
posted 20yrs
posted by jfnewell
9 comments
posted 20yrs
posted by jfnewell
aluminium extrusion from China
Norinco is a aluminium extrusion manufacturer in China, producing aluminium 6063,6061 extrusions in many surface finish...
7 comments
posted 20yrs
posted by fred.ku.alu
7 comments
posted 20yrs
posted by fred.ku.alu
Re-Enamel Stove burner tops & Grates
Have a gas stove with grey ceramic coated flat discs on top of burners, same colored enameled cast iron grates. Enamel...
1 comments
posted 20yrs
posted by goog.t.wilmington
1 comments
posted 20yrs
posted by goog.t.wilmington
Metal for backhoe
In the process of designing a backhoe for my Bobcat. What metal is suggested for the booms and the frame? As always the...
1 comments
posted 20yrs
posted by sale_items
1 comments
posted 20yrs
posted by sale_items
HF Mill/Drill
Does anyone have any experience with the HF Mill #33686-4VGA? Thanks..John
13 comments
posted 20yrs
posted by jbcimino
13 comments
posted 20yrs
posted by jbcimino
Welding "Anti-Stick"?
Hi, Is there some compound or liquid that I can spray or rub on between parts that will keep them from fusing from the...
9 comments
posted 20yrs
posted by planet10
9 comments
posted 20yrs
posted by planet10
Gilson Monty Ward owner's manuals on Ebay
due to high demand, I will be offering complete scanned copies of the Gilson owner's manuals on Ebay, if interested go t...
1 comments
posted 20yrs
posted by winchester1886
1 comments
posted 20yrs
posted by winchester1886
Solid state relay derating for motors
I have a 25A SSR that is spec'd "motor load 7.2 FLA". What is it about motor loads that require such drastic derating? I...
0 comments
posted 20yrs
posted by bobengelhardt
0 comments
posted 20yrs
posted by bobengelhardt
PULLEY MEASUREMENT
Another dumb question......Is the diameter of a pulley measured by the overall outside diameter or the smaller inside di...
3 comments
posted 20yrs
posted by lcrumley
3 comments
posted 20yrs
posted by lcrumley
impact wrench
I have what I thought was a decent quality cambell hausfeld 1/2" gun which is rated at 380 ftlbs. All fitting are 1/4"...
45 comments
posted 20yrs
posted by habbi
45 comments
posted 20yrs
posted by habbi
Garage door opener
Has anyone ever bypassed the electric eye in a garage door opener? Some value resistor should simulate a properly adjust...
13 comments
posted 20yrs
posted by fordnut
13 comments
posted 20yrs
posted by fordnut