⏣ General Metalworking

30777 Threads Posts
to

1960's Mattel Injector - resin used?

I just picked up a Mattel Injector toy injection molding machine. Does anyone have any idea what plastic resin was used...
8 comments posted 21yrs
posted by MichaelHenry
8 comments posted 21yrs posted by MichaelHenry

cut off disk shaft ?

i havee a very powerful hand grinder with 1/4 " collett--i want to use a cutoff disk 3" in diameter--it has a 1/4" hole...
6 comments posted 21yrs
posted by plener
6 comments posted 21yrs posted by plener

South Bend cross slide thrust bearing source?

I have a South Bend "Heavy 10" and one of the thrust bearings in the cross slide is shot. Anyone have a source for these...
5 comments posted 21yrs
posted by 9ekdu
5 comments posted 21yrs posted by 9ekdu

tubing bender die question

In the interest of celebrating the fact that it's not 120 degrees in my garage anymore, I decided to make a tubing bend...
11 comments posted 21yrs
posted by WanderingMetalHead
11 comments posted 21yrs posted by WanderingMetalHead

lathe chuck centering--newbee

new to all of this i have a jewlers chuck--lathe lorch model mm400 using adial indicator seems that the chuck has a hig...
1 comments posted 21yrs
posted by plener
1 comments posted 21yrs posted by plener

Pans for a small Hydraulic press

Looking for some suggested ways to build a small press out of scrap steel and a bottle jack. Need to rebuild a water pu...
14 comments posted 21yrs
posted by eyrse
14 comments posted 21yrs posted by eyrse

Sebastian Lathe (Ohio) Parts On Ebay

I know some people are looking for Sebastian parts so check out my auction to see if they are what you need. #7556849660...
0 comments posted 21yrs
posted by kndroy
0 comments posted 21yrs posted by kndroy

Car Body Sheetmetal-Old Leadwork Geezer Needed

Back on the Roadster Project. The series is here: http://www.seanet.com/~jasonrnorth/acc2.html I need to find a good, k...
16 comments posted 21yrs
posted by jasonrnorth
16 comments posted 21yrs posted by jasonrnorth

OT - Trane Furnace Problem

I have a Trane XL90 furnace (high effic, two stage) that goes into a fault condition every once in a while and will not...
5 comments posted 21yrs
posted by nospam
5 comments posted 21yrs posted by nospam

How is bright zinc plating achieved?

Hi all, I can tell hot dip galvanising and bright zinc plating apart (the former creates a thick, dull layer of zinc in...
8 comments posted 21yrs
posted by cdt22NOSPAM
8 comments posted 21yrs posted by cdt22NOSPAM

Vacuum pump id? GS-100Z

Hi, I'm in Bangladesh and I've been unable to buy a new Vacuum pump in the local market here (although I was interested...
3 comments posted 21yrs
posted by Modartis
3 comments posted 21yrs posted by Modartis

Looking for source

Anyone know of a good (cheap) source online for stainless steel sheetmetal? I'm trying to fabricate some square-to-round...
6 comments posted 21yrs
posted by pdave99
6 comments posted 21yrs posted by pdave99

Making or acquiring a 26mm end mill holder?

I happen to have a nice Nikken metric boring head that was designed to fit a 26mm BT-flange holder. This boring head ha...
12 comments posted 21yrs
posted by no-spam
12 comments posted 21yrs posted by no-spam

Vice slip debriefing

Hello all, Owner/operator and machine appear to be fine, but I had an incident this evening, and am curious what (else)...
12 comments posted 21yrs
posted by bschwab
12 comments posted 21yrs posted by bschwab

OT - removing paint

Is there any way to restore a mail pouch barn that was painted over with white paint? Thanks.
1 comments posted 21yrs
posted by stone75
1 comments posted 21yrs posted by stone75