⏣ General Metalworking

30777 Threads Posts
to

Bridgeport shaping attachment?

Regarding those shaper attachments that you bolt onto the back of a Bridgeport-like mill, is the back and forth sliding...
3 comments posted 21yrs
posted by no
3 comments posted 21yrs posted by no

flame cutting guide with speed governor

In his book "Shop Savvy" Roy Moungovan of Popular Science describes a flame cutting guide which has a "clockwork govern...
6 comments posted 21yrs
posted by grant
6 comments posted 21yrs posted by grant

Dust collector from HarborFreigh

Anyone has a dust collector from HarborFreigh ITEM 94029-0VGA? Is it any good? Thanks.
6 comments posted 21yrs
posted by alexkuzn
6 comments posted 21yrs posted by alexkuzn

Tesla Turbine

Some time ago somebody (forgotten who) mentioned, in passing, that hard drive discs might serve as rotors in a Tesla Tu...
25 comments posted 21yrs
posted by PGJSCAYQVANK
25 comments posted 21yrs posted by PGJSCAYQVANK

Milawukee comes through!

You all may recall a post I made last week concerning a refused warranty repair on a Milwaukee worm drive saw. Well I a...
7 comments posted 21yrs
posted by alanganes
7 comments posted 21yrs posted by alanganes

Help identifying Palmgren table?

Just acquired an 8" table that has X & Y travel, tilts and rotates. Similar to their current model 84, no. 32804 here:...
5 comments posted 21yrs
posted by tkee(no spam)
5 comments posted 21yrs posted by tkee(no spam)

OT - But vaguely funny

This is from "Thog's Masterclass" (http://www.dcs.gla.ac.uk/Ansible/thog.html), a listing of bad writing from Science F...
2 comments posted 21yrs
posted by jpolaski
2 comments posted 21yrs posted by jpolaski

Design Advise: Variable Stroke Crank

On and off I'm designing a shaper head for a horizontal miller which is driven by the miller's spindle. I'm at the poin...
12 comments posted 21yrs
posted by y2k
12 comments posted 21yrs posted by y2k

4" Abrasive cuttoff saw

Hey, I'm looking for a 4" abrasive cutoff saw and finding that they are pretty expensive for what they are. I had used...
9 comments posted 21yrs
posted by ed
9 comments posted 21yrs posted by ed

Herbert 4 Senior Pre-optive Lathe Problem

After being in storage for about 10 years I have relocated an old Herbert 4 Senior Lathe to a new workshop. I was worki...
5 comments posted 21yrs
posted by georgewbell
5 comments posted 21yrs posted by georgewbell

OT: Gunner Info on the Ham gear

Here's the info on the Ham gear I mentioned: I have no idea if any of it works. Heathkit Transmitter Model DX40 Heathki...
10 comments posted 21yrs
posted by kfvorwerk
10 comments posted 21yrs posted by kfvorwerk

Brazing help?

I'm attempted to do some brazing, never done it before, although I have soldered some copper pipes before! I have a pie...
13 comments posted 21yrs
posted by SomeOne
13 comments posted 21yrs posted by SomeOne

OT-Brady Lies again

http://www.americanchronicle.com/articles/viewArticle.asp?articleID=1326 So..whats new? Gunner Confronting Liberals wit...
3 comments posted 21yrs
posted by gunner
3 comments posted 21yrs posted by gunner

myford super 7 alternatives in USA?

I have an ancient ML-7 now, very well worn. I'm considering replacing it with something newer, ideally, with a quick ch...
5 comments posted 21yrs
posted by dwarner22
5 comments posted 21yrs posted by dwarner22