⏣ General Metalworking

30777 Threads Posts
to

Buffalo Punches and Dies

I have a flypress with an arbour & dieholder that take (as far as I can determine) Buffalo punches and dies - the dies...
1 comments posted 21yrs
posted by moby
1 comments posted 21yrs posted by moby

What is it? LXXXII

http://puzzlephotos.blogspot.com/ Rob
22 comments posted 21yrs
posted by rhvp67
22 comments posted 21yrs posted by rhvp67

Elongated Squirrel Fan(s)

Where can I find elongated squirrel fans like they use in copiers? I tossed all the ones I had and now NEED one to many....
6 comments posted 21yrs
posted by mattsonsolar
6 comments posted 21yrs posted by mattsonsolar

Harbor freight compressor pump opinions?

My 5 HP Sanborn air compressor developed a rod knock and died. Harbor freight has a replacement pump for $99. I goggled...
6 comments posted 21yrs
posted by Shakascaregiver
6 comments posted 21yrs posted by Shakascaregiver

Hydroforming with urethane

Just for sport, I made a die the other night from 6061t6511 The deepest details in the cavity were .06" The sheet sampl...
0 comments posted 21yrs
posted by gromit68
0 comments posted 21yrs posted by gromit68

Tool Definitions

Probably the best tool descriptions I have ever seen. DRILL PRESS: A tall upright machine useful for suddenly snatching...
1 comments posted 21yrs
posted by tomcarlsonREMOVE
1 comments posted 21yrs posted by tomcarlsonREMOVE

Aging steel and cast-iron?

Hi Folks, Not sure if this is the right place to post, but here goes. I need to age steel and cast iron. Basically, wha...
6 comments posted 21yrs
posted by pegboy_30
6 comments posted 21yrs posted by pegboy_30

which steel for load?

I have the choice of 4140, 1018, 12L14, 1045 cold rolled, W1 Drill rod, O1 Drillrod, A2 Drillrod for a 1.125 diameter r...
3 comments posted 21yrs
posted by soundadv
3 comments posted 21yrs posted by soundadv

Cliff and Kadaitcha Man

I'm sure I speak for all the metalworkers when I acknowledge that you're two of the most hardcore trolls we've ever see...
1 comments posted 21yrs
posted by cdt22NOSPAM
1 comments posted 21yrs posted by cdt22NOSPAM

Modern Equivalent of Watchmaking?

Since mechanical watchmaking has been obsoleted (AFAIK) I'm curious what current industry is similarly motivated to dev...
11 comments posted 21yrs
posted by galt_57
11 comments posted 21yrs posted by galt_57

LED flashlights -- a phlashlite phreak's phavorite

There's a bewildering myriad of LED flashlights out there to choose from. My personal favorite is, unfortunately, no lo...
3 comments posted 21yrs
posted by dforeman
3 comments posted 21yrs posted by dforeman

Tool holders for Smithy?

We have a Smithy Granite 1324 in the machine shop that lacks adequate tooling. It has the 4-way indexable turret tool p...
3 comments posted 21yrs
posted by jim.wilkins
3 comments posted 21yrs posted by jim.wilkins

HEat treating in my shop

I need to repair a dump trailer because the jack on the front has twisted and honestly is in the wrong spot. Because of...
7 comments posted 21yrs
posted by NoSpam
7 comments posted 21yrs posted by NoSpam

Free Potters Kickwheel

From a Freecycle forum Message: 9 Date: Tue, 04 Oct 2005 17:08:28 -0000 From: "cc4stuff" Subject: offer: potters kick wh...
1 comments posted 21yrs
posted by gunner
1 comments posted 21yrs posted by gunner

rollforming

Is there anybody tell me about the roll forming?
9 comments posted 21yrs
posted by webmaster
9 comments posted 21yrs posted by webmaster