⏣ General Metalworking

30777 Threads Posts
to

FS: A-2 tool steel plates

I'm in San Carlos, CA. (About 15 miles south of SFO Airport) I have several 24" x 22" x .75" and 22" x 21" x .5" A-2 to...
1 comments posted 21yrs
posted by akushner
1 comments posted 21yrs posted by akushner

Another knife

http://webpages.charter.net/dawill/Images/Knife22.jpg A lot lighter than last one, uh under a pound I'd guess. Curve ju...
1 comments posted 21yrs
posted by tmoranwms
1 comments posted 21yrs posted by tmoranwms

Where to buy metal stocks in the Bay Area?

I've been to the local hardware stores and big box places like Home Depot but they are limited in metal stocks like tub...
14 comments posted 21yrs
posted by Fred
14 comments posted 21yrs posted by Fred

LED flashlights: worth a darn?

I am in the market for a few flashlights to keep by our bedsides in case of emergency and want to know if LED flashligh...
92 comments posted 21yrs
posted by bsa441
92 comments posted 21yrs posted by bsa441

Carbide form tool

Greetings all, I'm in the final stages of milling a large spur gear (5.5" dia 11 tooth) for repair of an old excavator....
11 comments posted 21yrs
posted by Meyerga00
11 comments posted 21yrs posted by Meyerga00

Concentric bolt circles?

I need to make a couple of adapter plates for the new 56HP Yanmar to fit the CV joint to the prop shaft. The gear box f...
8 comments posted 21yrs
posted by gashmore
8 comments posted 21yrs posted by gashmore

Miller 35 wirefeed welder info request

I have a very ancient Miller 35 wirefeed welder that I need information on for the eventualty when it breaks. If someon...
4 comments posted 21yrs
posted by clutch
4 comments posted 21yrs posted by clutch

Mig Welder Covers

Just a heads up for those of you in California and close to the 99c store known as "99c Only" They are selling a very n...
3 comments posted 21yrs
posted by gunner
3 comments posted 21yrs posted by gunner

An update on my TIG inverter project

IMPORTANT, I am not trolling, and if I am asking stupid questions, that's due to my ignorance and malice. A while ago I...
34 comments posted 21yrs
posted by ignoramus29341
34 comments posted 21yrs posted by ignoramus29341

air pump repair

There's a little air pump on my torpedo kerosene heater. It wants to bind and stall, kicking out the overload. I just f...
13 comments posted 21yrs
posted by karltownsend.NOT
13 comments posted 21yrs posted by karltownsend.NOT

Anyone got a spare "Slydlok" 30 A fuse holder?

Hi all, Yesterday I picked up two 2 kVA 230 V -> 110 V transformers. One I plan to use to run 110 V tools in the worksh...
3 comments posted 21yrs
posted by cdt22NOSPAM
3 comments posted 21yrs posted by cdt22NOSPAM

Straightening the stainless weld job

Gentlemen, I am a novice TIG welder on my fifth Argon bottle (small one) After what I thought to be a reasonable amount...
13 comments posted 21yrs
posted by borism_-void-_
13 comments posted 21yrs posted by borism_-void-_

1996 Blazer AC Request not working

Since this group seems to be the keeper of all(nearly) knowledge, I thought I would start here.... I have a 1996 Blazer...
6 comments posted 21yrs
posted by cyberzl1
6 comments posted 21yrs posted by cyberzl1