⏣ General Metalworking

30777 Threads Posts
to

Looking for a Source for DIN 610 Shoulder Bolts

Does anyone know of a source in the U.S. for DIN 610 Shoulder Bolts. Exact specification is M12 x 50. Thanks you.
1 comments posted 21yrs
posted by Inthemedia
1 comments posted 21yrs posted by Inthemedia

90 lbs battery charger

I have a very heavy military surplus 12V battery charger. Maybe 80 lbs (WAG). I could not sell it. It works, but is hea...
6 comments posted 21yrs
posted by ignoramus18245
6 comments posted 21yrs posted by ignoramus18245

Experience with quenching a red hot steel rod

Ladies and Gentlemen, I want to ask you if you have experienced or know of any stories about a particular phenomenon wh...
9 comments posted 21yrs
posted by s.morra
9 comments posted 21yrs posted by s.morra

Facom nut splitter

My Facom nut splitter set has arrived and I tried it out yesterday. Cuts nuts open nicely. I removed 6 seriously rusty...
3 comments posted 21yrs
posted by cdt22NOSPAM
3 comments posted 21yrs posted by cdt22NOSPAM

Enco gloat

Just got in my latest buy from Enc. Nice halogen swing arm lamp, marked down from $64 to $20. This along with the free...
17 comments posted 21yrs
posted by abuse
17 comments posted 21yrs posted by abuse

question

Hi, I'm just trying to make a mold with plaster + kaolin (25% + 75 %) to hold bronze. The mold works fine but the final...
13 comments posted 21yrs
posted by lehmann[quitthat]
13 comments posted 21yrs posted by lehmann[quitthat]

OT: Riding lawnmower problem (lotsa smoke)

Hi all. My wife was cutting the grass the other day when the lawnmower engine (Briggs and Stratton) started smoking in...
27 comments posted 21yrs
posted by misterpaslowCAPS
27 comments posted 21yrs posted by misterpaslowCAPS

Tube bending problem update

About ten days ago, I posted that I had been having a problem finding a tube bender to bend some .020" x 1.125" 304 sta...
1 comments posted 21yrs
posted by gjpostma
1 comments posted 21yrs posted by gjpostma

Anyone know lots about trucks / trailers?

Who is the largest trailer manufacture for big rig boxes? Wabash is second I think, but who is first? Alternate bonus qu...
17 comments posted 21yrs
posted by bob
17 comments posted 21yrs posted by bob

Need gears for K&T mill

Broke a few gears on a K&T number 3 hoz. mill Anyone know where can I find some. Thanks in advance. Tim Kallam
4 comments posted 21yrs
posted by tlkallam
4 comments posted 21yrs posted by tlkallam

a note on trav-a-dial repairs

thanks to the good offices of one of the NG denizens, I acquired a couple of sick trav-a-dials. both were sticky. hee i...
6 comments posted 21yrs
posted by nobody
6 comments posted 21yrs posted by nobody

Drill & tap compressor tank?

I've got an old 20 gal (?) compressor tank in which I want to install a drain. I'm guessing it to be 1/4-inch (6.3 mm?)...
23 comments posted 21yrs
posted by me
23 comments posted 21yrs posted by me

CNC controller for sale

I have a 3-Axis CNC control for sale. Can be used with brushed or brushless servo motors up to 12.5A peak per axis from...
0 comments posted 21yrs
posted by technologic
0 comments posted 21yrs posted by technologic

Lathe Tooling?

Our robotics team just acquired an old Craftsman 12" lathe and it came with limited tooling. If anyone in the SF Bay Ar...
7 comments posted 21yrs
posted by woodworker88
7 comments posted 21yrs posted by woodworker88

bracket strength

Does anyone know the PSI rating for the l shaped brackets you find at Home Depot. These are the ones in the roofing are...
12 comments posted 21yrs
posted by carruths
12 comments posted 21yrs posted by carruths