⏣ General Metalworking

30777 Threads Posts
to

punch source

Some of you may recall my motorcycle mishap june 7 2003, I am walking and wonders, working again. Gettin fat and lovin'...
4 comments posted 21yrs
posted by wwsnot
4 comments posted 21yrs posted by wwsnot

Unforseen Solidworks problem

I've been doing a flurry of design work for the past few months. If you remember my post a few months ago about changin...
3 comments posted 21yrs
posted by tom(nospam)
3 comments posted 21yrs posted by tom(nospam)

Best chemical cleaner for old mechanical junk?

Any suggestions for a good homemade total immersion type chemical cleaner/degreaser for antique mechanical restoration...
14 comments posted 21yrs
posted by fdavidander
14 comments posted 21yrs posted by fdavidander

something cool yesterday

My son got his bicycle chain all caught around the crank. The only solution was to pull the crank off, for which I need...
16 comments posted 21yrs
posted by bill
16 comments posted 21yrs posted by bill

compressor head gasket

The latest replacement head gasket on my old Kellogg-American TVS201 2 cylinder air compressor blew out again at the na...
7 comments posted 21yrs
posted by jim.wilkins
7 comments posted 21yrs posted by jim.wilkins

Did Sherline let down - not!

One failing with Sherline - if they have any failings at all - might be the maximum speed of the lathe spindle. While c...
7 comments posted 21yrs
posted by judybob
7 comments posted 21yrs posted by judybob

Got Model Engine Builder

Got my first two issues of Model Engine Builder, and I'm delighted. Drawings are 11 x 17, folded and stuck into mag wit...
3 comments posted 21yrs
posted by stauffer
3 comments posted 21yrs posted by stauffer

stiff three jaw

We have a three jaw chuck ( Bison brand) on our old lathe at work. The chuck is about 18 inches in diameter. It is a br...
5 comments posted 21yrs
posted by m-zimmerman
5 comments posted 21yrs posted by m-zimmerman

What is it? LXXI

Just posted another set: http://puzzlephotos.blogspot.com/ Rob
21 comments posted 21yrs
posted by rhvp67
21 comments posted 21yrs posted by rhvp67

fa: - Hoke/Phonix regulator dated 1961 -

I'm getting rid of a few regulators - this particular one is in very nice cosmetic condition (no idea about functionali...
0 comments posted 21yrs
posted by nobody
0 comments posted 21yrs posted by nobody

Source for 1/2-8 LH Precision Acme Lead Screw

I need a source for 1/2-8 LH Precision Acme Lead Screw for the cross slide of my Sheldon Lathe. The specs are listed be...
5 comments posted 21yrs
posted by Sierevello
5 comments posted 21yrs posted by Sierevello

Rockwell 11 Spindle Bearings

My new lathe has double tapered timken roller bearings on the front of the spindle. It had set for a while so I figured...
15 comments posted 21yrs
posted by rohamm
15 comments posted 21yrs posted by rohamm

Coolant pump on a lathe

So, this lathe I bought has an integral coolant pump. I never used a machine with one, so am looking for some basic gui...
15 comments posted 21yrs
posted by notreally
15 comments posted 21yrs posted by notreally

Realy cool site

Let's see if I can remember how this works... Oh yah, Hey everybody, I found this real cool site... http://www.ibiblio.o...
2 comments posted 21yrs
posted by NO.SPAM
2 comments posted 21yrs posted by NO.SPAM