⏣ General Metalworking

30777 Threads Posts
to

Motor/Generator Analysis

I have measured the DC resistance of a split-phase capacitor run induction motor's two windings. They are 53 and 35 ohm...
50 comments posted 21yrs
posted by DGoncz
50 comments posted 21yrs posted by DGoncz

OT Counting rivets quality issue

I am looking for a counter to count groups of rivets installed using a Briv gun. I found a couple of counters on the WW...
2 comments posted 21yrs
posted by rwesttx
2 comments posted 21yrs posted by rwesttx

Holdiays and Calls for Jobs?

Anyone else notice an increase in calls just prior to a holiday and then a decrease afterwards? I attribute it to the f...
1 comments posted 21yrs
posted by bob
1 comments posted 21yrs posted by bob

Brain picking: Need some ideas/direction

Hi folks. I was hoping that someone here might have an idea that would send a project a different direction; Basically...
21 comments posted 21yrs
posted by kmiller
21 comments posted 21yrs posted by kmiller

CNC drilling question

Which would be more accurate for a servo based setup using a step compatible drive; 1. Use screw TPI, gear ratio data,...
2 comments posted 21yrs
posted by oparr
2 comments posted 21yrs posted by oparr

centering round disc ?

1/8" thick 4" diameter steel circle. has a 1" hole in center. I want to stack many of these and drill holes in them. Ho...
7 comments posted 21yrs
posted by aiiadict
7 comments posted 21yrs posted by aiiadict

Dipping into the knowledge Base

Yesterday, I met with a company that is prolly going to build a machine for one of my clients. In my discussion with th...
3 comments posted 21yrs
posted by gjpostma
3 comments posted 21yrs posted by gjpostma

Drilling out taper pins

I have to punch out 5 or 6 #7 taper pins that are in a very bad position. If I can't get any out what are the thoughts...
16 comments posted 21yrs
posted by r.robinson
16 comments posted 21yrs posted by r.robinson

OT small compressor suggestions

I'm looking for suggestions for which brand/model portable compressor to buy. Primary purpose will be operating a frami...
4 comments posted 21yrs
posted by kfvorwerk
4 comments posted 21yrs posted by kfvorwerk

DoAll Lathe Threading Question

At work, we have a DoAll Lathe and was trying to cut 32 TPI with it. One thread chart jumped from 30 to 33 TPI. There w...
1 comments posted 21yrs
posted by regor
1 comments posted 21yrs posted by regor

What is the most fun metalworking?

I like cleaning the grease and dirt off and fixing 80 year old military rifles. Cleaning and fixing 50 year old lathes i...
41 comments posted 21yrs
posted by c.magnuson
41 comments posted 21yrs posted by c.magnuson

Tesla Turbine #3

first two were CD's on a skateboard bearing.... new turbine: 1 hard disk from a PC 1 2" piece of 1/8" tubing 1 small pi...
0 comments posted 21yrs
posted by aiiadict
0 comments posted 21yrs posted by aiiadict

HVLP crash course

I currently have a Sears compressor and paint pot sprayers. I was wondering how the HVLP systems compare. My main quest...
3 comments posted 21yrs
posted by desertNOSPAMtraveler
3 comments posted 21yrs posted by desertNOSPAMtraveler

boiler plans?

Hello, I am looking for plans for a steam boiler. Heat source: 1.5' diameter circle. The boiler has to transfer the hea...
9 comments posted 21yrs
posted by aiiadict
9 comments posted 21yrs posted by aiiadict