⏣ General Metalworking

30778 Threads Posts
to

440C Stainless Problem

We are having a problem drilling some 440C stainless steel. Anyway we are drilling 1/8" holes 1/4" deep. We have been u...
3 comments posted 21yrs
posted by tazznchop
3 comments posted 21yrs posted by tazznchop

Lincoln Electric 225-GLM to Digital?

AC Buzz Box to Digital Amperage control. Anybody know if this would be possible and any hints on what I would need? To g...
3 comments posted 21yrs
posted by bert.eileen.plank
3 comments posted 21yrs posted by bert.eileen.plank

Engine machining and material question

I currently have a Kohler twin cylinder air cooled engine torn down on the bench. It's not well supported by the factor...
9 comments posted 21yrs
posted by albieguyspamless
9 comments posted 21yrs posted by albieguyspamless

OT post- Triac's

Sorry for the OT post, but I don't know a better group of knowledgeable folks to ask. As long as a triac is run within...
21 comments posted 21yrs
posted by edangellatcomcastdotnet
21 comments posted 21yrs posted by edangellatcomcastdotnet

Posters with VCF attachments

Just a heads up...Agent and other news readers will not allow the reading of your messages when you have a "business ca...
2 comments posted 21yrs
posted by gunnerNOSPAM
2 comments posted 21yrs posted by gunnerNOSPAM

how to make deep drilling tool?

anyone got some information on how to make deep drilling tool? The OD needs to be 40mm and lenght 1meter.
22 comments posted 21yrs
posted by nkrbjhvee
22 comments posted 21yrs posted by nkrbjhvee

Peltier cooler

Anyone know anything about Peltier coolers. A friend of mine wants to cool 12"x15"x30" glass vivarium a maximum of 20-3...
33 comments posted 21yrs
posted by kfvorwerk
33 comments posted 21yrs posted by kfvorwerk

OLD Tractor Stuff

Howdy ;-) http://www.ytmag.com/index.htm http://www.antiquetractors.com/ Maybe some thing here to look at or some one to...
2 comments posted 21yrs
posted by scutt
2 comments posted 21yrs posted by scutt

Bought a drill press today

Well I bought a Delta DP300 today. my wife works at ACE Hardware and they have an ACE drill press on sale and their bro...
3 comments posted 21yrs
posted by pegleg1az
3 comments posted 21yrs posted by pegleg1az

OT looking for plans for an auto lift

Would anyone have some plans for an auto lift, or a ramp of some kind to lift a small car/truck up about 36 inches. I k...
1 comments posted 21yrs
posted by gowens1
1 comments posted 21yrs posted by gowens1

MIG (GMAW) welding SS gas question

Greetings all, We ran out of Ar/He (75/25 I think) mix while welding some 3/4" SS today. The "weldor" loaded a bottle o...
1 comments posted 21yrs
posted by jimnthem_AT_comcast_DOT_net
1 comments posted 21yrs posted by jimnthem_AT_comcast_DOT_net

Practical Oxo Acetyline Welding 1938 FA

Great old Welders handbook from 1938 by R Granjon,P Rosemberg & A Desgranges. Pub. The Welding Journal ,(Raggett & Co.)...
1 comments posted 21yrs
posted by linda_beynon
1 comments posted 21yrs posted by linda_beynon

work hardening in brass

I have a cast brass foot from an incense boat, (not that it matters, but if you know what that is, it might give you a...
48 comments posted 21yrs
posted by jwhall
48 comments posted 21yrs posted by jwhall

Broaching problems

Hello all We have a Hansford/Davis Keyseater at work and we are getting a lot of chatter in the bottom of the keyway. S...
8 comments posted 21yrs
posted by machineman
8 comments posted 21yrs posted by machineman