⏣ General Metalworking

30778 Threads Posts
to

Fireman's pole

This might sound ridiculous to some but I am building a new house which has a loft and I am putting a "fireman pole" in...
25 comments posted 21yrs
posted by habbi
25 comments posted 21yrs posted by habbi

Oil Feed Drill Question

For the drills with the oil feed holes parallel to the shank, which run from one end of the drill to the other, is a di...
5 comments posted 21yrs
posted by eugene
5 comments posted 21yrs posted by eugene

OT - 1919 Illinois brand tractor

I've Googled and surfed with no success. I've left messages on several forums. No luck. I have an owner's manual and pa...
14 comments posted 21yrs
posted by andyasberry
14 comments posted 21yrs posted by andyasberry

1 3/4 inch step drill bit ?

I need to drill a 1 3/4 inch hole in ABS plastic. I presently have great luck doing this with smaller holes, up to an i...
11 comments posted 21yrs
posted by cps
11 comments posted 21yrs posted by cps

Flat belt on Logan lathe Model 200

I've finally got my little Loagan Model 200 up and running. Seems to be nice and tight, cuts the nicest collection of s...
5 comments posted 21yrs
posted by spamless
5 comments posted 21yrs posted by spamless

Does anybody sell pre-made dovetail stock?

I am building a small project using only stock parts requiring no additional machining. I want to buy a small piece of...
8 comments posted 21yrs
posted by tomandasha
8 comments posted 21yrs posted by tomandasha

casting 316 stainless

I'm new to this, so forgive me if this is a stupid question: Can I cast 316 stainless steel using an oxy-acy torch? I'm...
5 comments posted 21yrs
posted by twocranks1
5 comments posted 21yrs posted by twocranks1

Page update

--Updated a few sections of my webpage. If anyone's got input please don't forget to tell me *which* section needs the...
2 comments posted 21yrs
posted by steamer
2 comments posted 21yrs posted by steamer

Technical Video Rental

If folks will pardon a quick plug: I'd like to mention the website http://technicalvideorental.com We rent out lots of...
6 comments posted 21yrs
posted by tjic_googlegroups
6 comments posted 21yrs posted by tjic_googlegroups

Taig Cross Slide Problem Fixed

I recently posted here about the cross slide problem where it was binding. Therre is a brass nut that needed to be "wor...
1 comments posted 21yrs
posted by msterspy
1 comments posted 21yrs posted by msterspy

OT: NIST Study Of CD/DVD Longevity

Hi all, Really no metalworking content, but interesting, and concerns something most of us use regularly... found it re...
11 comments posted 21yrs
posted by erik
11 comments posted 21yrs posted by erik

Grizzly G1008 Spindle Lock

The spindle lock on my Grizzly G1008 knee mill doesn't do a very good job of locking the spindle. It never has. Unless...
2 comments posted 21yrs
posted by n5kzw
2 comments posted 21yrs posted by n5kzw

LeBlond Paint Color

Does anyone have the paint code for LeBlond Servoshift lathes? I have a 1964 that has been repainted a non-original col...
2 comments posted 21yrs
posted by jborning
2 comments posted 21yrs posted by jborning

Screw recomendation needed

I have an application to attach a cup brush with a 1/2" arbor hole to a plastic handle. The brush fits into a 3/8" deep...
4 comments posted 21yrs
posted by tom(nospam)
4 comments posted 21yrs posted by tom(nospam)

Pics of 1902 Mill in Dropbox

Hello, I hope everyone enjoyed the pics of the Calusing with dro. Perhaps someone can identify this old horizontal mill...
0 comments posted 21yrs
posted by doozer75
0 comments posted 21yrs posted by doozer75