⏣ General Metalworking

30778 Threads Posts
to

Help Needed: Harding 3J chuck stuck

Hello, While turning close to my chuck my Aloris tool holder handle rubbed on the rubber grip/handle of my Harding-Sjog...
1 comments posted 21yrs
posted by user
1 comments posted 21yrs posted by user

Proper RPMs for Snow Blower Engine?

I've got a feeling the governed full speed RPM of the 6 HP Tecumseh "Snow King" engine on my 1964 Ariens Sno-Thro has b...
79 comments posted 21yrs
posted by jwisnia
79 comments posted 21yrs posted by jwisnia

PLEASE!!! help with older Airco arc welder

Hi all, I recently was given an old (1980's??) Airco "EasyARC" A/C arc welder. I haven't done any welding in about 10 y...
4 comments posted 21yrs
posted by djrabin
4 comments posted 21yrs posted by djrabin

Miter Gears

I am looking to make a couple of tables that raise and lower. Each would have a handle at one end, which when turned li...
12 comments posted 21yrs
posted by eric.d.wilson
12 comments posted 21yrs posted by eric.d.wilson

Taper thread turning

Hi group, I want to make a 1" BSPT taper pipe thread tap. Okay I can cut the pitch on my lathe okay and that would be f...
14 comments posted 21yrs
posted by donttry
14 comments posted 21yrs posted by donttry

FAQ/Guide?

Is there a FAQ or guide floating around on how to clean and setup up a new 7 x 10?
2 comments posted 21yrs
posted by grady3
2 comments posted 21yrs posted by grady3

Heavy moving with a DRW pickup ?

I am buying a new pickup. There is only about $300 difference between the SRW (single rear wheel) and DRW (dual rear wh...
6 comments posted 21yrs
posted by samiam
6 comments posted 21yrs posted by samiam

Orientation of Timken Tapered Roller Bearing

I just took the spindle apart on my Sheldon and noticed on the rear bearing that there is a dimple on the face of the b...
11 comments posted 21yrs
posted by Sierevello
11 comments posted 21yrs posted by Sierevello

Free engineering reference book

I was searching for a formula to design torsion springs, and discovered this free engineering reference with a huge, de...
4 comments posted 21yrs
posted by kinch
4 comments posted 21yrs posted by kinch

Machinist's Handbook 26 as an e-Book

A friend of mine recently sent me a heads up. Someone posted Machinist's Handbook #26 on newsgroup alt.binaries.e-book....
65 comments posted 21yrs
posted by kabowers
65 comments posted 21yrs posted by kabowers

McMaster Catalog Gloat

I spent the week before last in New Jersey on a scaleup run at our contract manufacturer's location. I made daily runs...
16 comments posted 21yrs
posted by keillorp135
16 comments posted 21yrs posted by keillorp135

Interferance fit

How much material should I leave for an interferance fit? I need to make a part for my mortiser. It's a shaft that is u...
1 comments posted 21yrs
posted by mphee
1 comments posted 21yrs posted by mphee

B&S Collets from Hardinge

You guys, may remember, that a few weeks ago, I was looking for a good source for B&S collets for my new dividing head....
16 comments posted 21yrs
posted by abrasha
16 comments posted 21yrs posted by abrasha

Oxygen

Hi there! I am just hoping to start working with a propane/oxygen welding/heating torch. I am just wondering if anybody...
16 comments posted 21yrs
posted by samantha.thompson79
16 comments posted 21yrs posted by samantha.thompson79