⏣ General Metalworking

30778 Threads Posts
to

Metal Lathe Accessories

MLA owner Andy Lofquist is working hard on a new kit: a tool and cutter grinder. It sounds like an interesting design....
0 comments posted 21yrs
posted by deichles
0 comments posted 21yrs posted by deichles

Delta scroll saw pivot bushes

Picked up a botttom-of-the-line unit, quite a lot of slop side to side, of the blade. Discovered that the arm is pivote...
4 comments posted 21yrs
posted by mfraser
4 comments posted 21yrs posted by mfraser

FA: Machinists's Desk pen/ashtray

Just in case this might appeal to you metalheads. Cheap! :-) -- Bob (Chief Pilot, White Knuckle Airways) I don't have to...
2 comments posted 21yrs
posted by viewptmd
2 comments posted 21yrs posted by viewptmd

Air compressor switch shutoff problem

problem: I just purchased a switch to repair my old sears 1.5hp compressor. The original problem I had was there was a...
5 comments posted 21yrs
posted by google
5 comments posted 21yrs posted by google

FS Large Drills

I have a few 1.75 and 1.875 HSS MT4 shank drills for sale if anyone is interested 50.00 each email me jtoycen @ rogers.c...
2 comments posted 21yrs
posted by Sailor_Jeff
2 comments posted 21yrs posted by Sailor_Jeff

rack and pinion

The telescope I've referred to in recent postings has a pair of knobs joined by an axis whose center is a pinion that e...
79 comments posted 21yrs
posted by ara
79 comments posted 21yrs posted by ara

Convert Degrees to Foot Pounds?

Working on a Deutz Diesel engine. The instructions say to torque the bolts to 30 foot pounds then turn 45 degrees. Can...
95 comments posted 21yrs
posted by webmaster
95 comments posted 21yrs posted by webmaster

Bridgeport 2J Head noise

So there I was machining a piece of 304 cres on my Bridgeport to make a belt tensioning handle for my Heavy 10 lathe be...
1 comments posted 21yrs
posted by DaveNugent
1 comments posted 21yrs posted by DaveNugent

Compressor problem

I have a problem with my 4 hp cambell hausfeld oiless direct drive air compressor. When empty it will start and work fi...
9 comments posted 21yrs
posted by habbi
9 comments posted 21yrs posted by habbi

pro gun/anti-gun

Sure wish the pro/anti guys would take their petty bickering elswhere. Informational post are one thing, cheap shots and...
1 comments posted 21yrs
posted by gmasterman
1 comments posted 21yrs posted by gmasterman

FS -8 inch Kurt vise

I have a used Kurt 8" vise. Any one in the Portland - Salem OR area interested in it? I can email pictures if you want....
0 comments posted 21yrs
posted by raweich
0 comments posted 21yrs posted by raweich

Replace sintered bushing bearing?

Hi all. I picked up an old Millers Falls arbor at a flea market. It has a 1/2" shaft with bronze bearings. The bearings...
5 comments posted 21yrs
posted by aol.nospam
5 comments posted 21yrs posted by aol.nospam

Myford mandel nose

Hi, a few years ago i bought a short length of metal pre machined with a Myford ML7 mandrel nose machined on the end, i...
2 comments posted 21yrs
posted by jim
2 comments posted 21yrs posted by jim

cracked aluminum question?

Can a cracked aluminum head from an air compressor be fixed by a welder? It is cracked on the compressed air side, not...
1 comments posted 21yrs
posted by poolcuesNOJUNK
1 comments posted 21yrs posted by poolcuesNOJUNK

Another tool ID needed XXIV

Just posted another set of photos: http://puzzlephotos.blogspot.com/
35 comments posted 21yrs
posted by rhvp65
35 comments posted 21yrs posted by rhvp65