⏣ General Metalworking

30778 Threads Posts
to

Modifying a lathe to follow patterns

We want to be albe to cut curves of up to 44 in in length. They are gentle curves. Swamped rifle barrels to be specific...
3 comments posted 22yrs
posted by clannorm
3 comments posted 22yrs posted by clannorm

Something every metal worker NEEDS!

http://zapatopi.net/afdb.html Some ABSOLUTELY vital information and insight that can be applied to nearly any situation...
1 comments posted 22yrs
posted by deserttraveler
1 comments posted 22yrs posted by deserttraveler

cleaning metal for welding

Hello all, I have a beginner's question: I've been not having much success acetylene welding together pieces of rusty r...
10 comments posted 22yrs
posted by adriaang
10 comments posted 22yrs posted by adriaang

Rare and Odd Collets for sale Cheap

This is just a FYI but I was browsing at K Surplus in San Diego (a great source for fasteners and some suplus tooling a...
0 comments posted 22yrs
posted by dilligan
0 comments posted 22yrs posted by dilligan

Got an old drill press today

One of my customers unloaded a bunch of Stuff on me yesterday Among the Stuff was a Buffalo #13 drill press. 3 phase, t...
4 comments posted 22yrs
posted by gunnerNOSPAM
4 comments posted 22yrs posted by gunnerNOSPAM

Asking for advise on lapping/polishing

Hello everybody, I'm working on a small sterling engine project and I need to polish a steel piston (dia. 23/32 ") to a...
2 comments posted 22yrs
posted by mp1001
2 comments posted 22yrs posted by mp1001

Need source: Alum/Steel tray

7"(h) x 9.5"(w) x 1.3 deep. Any radius in the corners would need to be outside these dims. Could be a little higher, no...
2 comments posted 22yrs
posted by vrgolf
2 comments posted 22yrs posted by vrgolf

source for silver planchets?

I would like to attempt making some silver "family" coins for gifts this christmas. I have some rough attempts at a die...
9 comments posted 22yrs
posted by john213a
9 comments posted 22yrs posted by john213a

Help Lincoln MIG welder problem

I have a Lincoln SP-170 MIG and recently I started having trouble with it. It does not seem to weld as it used to. It d...
3 comments posted 22yrs
posted by habbi
3 comments posted 22yrs posted by habbi

Have questions

I had some of these made for me. I want to reproduce them to the best of my ability. Curious as to how these were press...
6 comments posted 22yrs
posted by twofas4luv2000
6 comments posted 22yrs posted by twofas4luv2000

cadillac lathe purchase - opinions?

I went to look at a cadillac 1440 lathe yesterday. Visually it looked ok, albeit well used, and there was a lot of back...
1 comments posted 22yrs
posted by rick
1 comments posted 22yrs posted by rick

Toolmakers Microscope

I recently got a Mitutoyo toolmakers microscope at a local auction. It's a neat unit, it has an xy table with micromete...
4 comments posted 22yrs
posted by aajnorm
4 comments posted 22yrs posted by aajnorm

Attaching cam to shaft

I want to attach a cam that is 1" wide, 2.5" dia and attach it to a 1" x 1' hard shaft. This will replace a cold-roll s...
12 comments posted 22yrs
posted by tom(nospam)
12 comments posted 22yrs posted by tom(nospam)

Help Picking Stainless Alloy?

I need to make some fittings for our bathroom. I'd like them to look like polished chrome to match some hardware they w...
5 comments posted 22yrs
posted by gwhite
5 comments posted 22yrs posted by gwhite