⏣ General Metalworking

30778 Threads Posts
to

Triple Gloat!

I don't usually get to gloat over a purchase as I am normally buying for resale. This last week I went to an auction wi...
9 comments posted 22yrs
posted by CATRUCKMAN
9 comments posted 22yrs posted by CATRUCKMAN

Value of an old lathe

I'm looking at an old lathe: No name on it anywhere....could be South Bend, but no plates anywhere No quick change gear...
2 comments posted 22yrs
posted by jmdmps
2 comments posted 22yrs posted by jmdmps

rust removal

i got this info from another newsgroup.. thought metal workers might have some interest in it.... to remove rust via ele...
1 comments posted 22yrs
posted by dbird
1 comments posted 22yrs posted by dbird

Machine shop need near Orlando

I need a reliable machine shop near Orlando to shave some cylinder heads. Any help?
2 comments posted 22yrs
posted by kdoney
2 comments posted 22yrs posted by kdoney

the Russian Anvil and what to do with it

OK. Because of the recommendations here on RCM I bought that anvil from HF. Got it home and then read the thread about...
21 comments posted 22yrs
posted by etpm
21 comments posted 22yrs posted by etpm

Unusual compression spring source needed?

I have a pinball machine that needs a specific spring, but the usual sources have to custom make them, resorting to a m...
5 comments posted 22yrs
posted by dragonbreed
5 comments posted 22yrs posted by dragonbreed

Yard Sale gloat

Bagged a 10" 1.5hp Baldor 3 phase bench grinder at a yard sale today, $15 with the lighted eye guards! This lists for o...
3 comments posted 22yrs
posted by janders
3 comments posted 22yrs posted by janders

Saugus Iron Works National Hisstoric Site

Last Sunday the Mass. College of Art Iron Guild put on a demonstration of iron casting at the Saugus Iron Works. A set...
7 comments posted 22yrs
posted by errol.groff
7 comments posted 22yrs posted by errol.groff

carbide parting tool

so. I'm a woodworker. I play with metalworking. as a woodworker, I end up with carbide tipped saw blades. sometimes I e...
9 comments posted 22yrs
posted by bridger
9 comments posted 22yrs posted by bridger

toolbox design

hi gang, been thinking of making a new toolbox at work but i need some design ideas. any freebie designs on the web? man...
0 comments posted 22yrs
posted by tittiesandbeer
0 comments posted 22yrs posted by tittiesandbeer

What capacitors to use for 1-3 phase connection?

I have forgotten what the configuration is for connecting a 3 phase motor to a single phase 220 volt supply with startin...
1 comments posted 22yrs
posted by nickalexander
1 comments posted 22yrs posted by nickalexander

Gib strip on vertical mill

Last week at my local tech college we stripped down an Elliot Vert Mill. When the carriage Gib strip came out it was br...
6 comments posted 22yrs
posted by hayjay1
6 comments posted 22yrs posted by hayjay1

Cleaning for Oxygen Service

Does anyone know where I can get a copy of these publications other than joining the CGA? O2-DIR "2000 Directory of Cle...
6 comments posted 22yrs
posted by argosys
6 comments posted 22yrs posted by argosys

Rebuild kit for old Walker floor jack--worth it?

I have a really, really old (cast iron hoods over the casters) Walker 1.5T floor jack. It has a lot of wear, but it giv...
8 comments posted 22yrs
posted by gto69ra4
8 comments posted 22yrs posted by gto69ra4

What brand US lathe to buy

One of these days I will give up on my 1942 Sheldom 11X40 and replace it with something newer. Just wondering what is o...
25 comments posted 22yrs
posted by gmasterman
25 comments posted 22yrs posted by gmasterman