⏣ General Metalworking

30778 Threads Posts
to

Reusing lock washers

Greetings! I'm working in a warehouse where they have a carton opener which blade held by a 10-32 screw. The practice W...
9 comments posted 22yrs
posted by avres
9 comments posted 22yrs posted by avres

Question from a newbie

Greetings. I have a question for this group. I operate a small auto accessory store. One of my products, made from 6061...
6 comments posted 22yrs
posted by twofas4luv2000
6 comments posted 22yrs posted by twofas4luv2000

Cleaning brass help needed!

Anybody know of a dip that will clean brass almost instantly? Or at least in a few minutes? That is sold at the store o...
12 comments posted 22yrs
posted by etpm
12 comments posted 22yrs posted by etpm

ID knurling tool and bore sleeving advice?

I have several rear hubs from vintage race MG Midgets that have spun their bearings, and I need to find a repair. The p...
3 comments posted 22yrs
posted by brian.evans
3 comments posted 22yrs posted by brian.evans

OT: hearing loss? cochlear implant--a story

My dad is 86 and flew on many bombing missions in a B24J during WWII and afterwards was a navigator for several years,...
8 comments posted 22yrs
posted by grantNOSPAM
8 comments posted 22yrs posted by grantNOSPAM

Gunner is doing fine

I've been told that he will be out of the hospital tomorrow. Sue
24 comments posted 22yrs
posted by sebrady
24 comments posted 22yrs posted by sebrady

Heat Treating Aluminum

I've been working with 2024 T3 sheets of various thicknesses, and am looking for some other alloy that can be heat trea...
3 comments posted 22yrs
posted by cgiese0001
3 comments posted 22yrs posted by cgiese0001

OT: Ebay for people overseas?

How do people get around getting stuff from Ebay when sellers won't post overseas? I can understand why they won't, wit...
5 comments posted 22yrs
posted by geoff_m
5 comments posted 22yrs posted by geoff_m

Indexing quill head on mill/drill

I have a mill/drill which satisfies my needs, but I have discovered at least one disadvantage to such a machine.. I som...
11 comments posted 22yrs
posted by rjscibienski
11 comments posted 22yrs posted by rjscibienski

Coating Tin Plated Steel

We use a bezzel that is made of .015 thick tin plated carbon steel. Apparently, the plating is done as a sheet and afte...
2 comments posted 22yrs
posted by rileyesi
2 comments posted 22yrs posted by rileyesi

Tube notcher

Question: If I have a vertical mill, do I need a tube notcher? Any of you using your mill for notching? Thanks, Ivan Veg...
6 comments posted 22yrs
posted by ivan
6 comments posted 22yrs posted by ivan

OT Gunners in the hospital

If some of you are wondering why there haven't been some cryptic responses from Gunner it is because he is very under t...
142 comments posted 22yrs
posted by CATRUCKMAN
142 comments posted 22yrs posted by CATRUCKMAN

i need a schematic for doall dbw 1a welder

I need a schematic for a dbw 1a blade welder. i believe it is one page. please email me if you can do this thanks
5 comments posted 22yrs
posted by asp3211968
5 comments posted 22yrs posted by asp3211968

OT cutting asphalt

We are intending to set up a set of rolls to feed material into our saw inside the buildng. Before we set up the rools...
11 comments posted 22yrs
posted by m-zimmerman
11 comments posted 22yrs posted by m-zimmerman