⏣ General Metalworking

30778 Threads Posts
to

3-phase breaker question

We installed a new sub-distribution box with 8 circuits replacing the 3 big circuits that were severely overloaded. Ove...
14 comments posted 22yrs
posted by tom
14 comments posted 22yrs posted by tom

Furnace heating element

After perusing posts about the Gingery furnace and visiting http://www.dansworkshop.com/The%20New%20and%20Improved%20Li...
23 comments posted 22yrs
posted by nodamned
23 comments posted 22yrs posted by nodamned

I know why isolation xmfr is used now

When wiring up some of the low wattage 115 volt circuits in the control cabinet I decided to use an xmfr to lower the v...
0 comments posted 22yrs
posted by etpm
0 comments posted 22yrs posted by etpm

Setting up flood coolant

Hi - I'm setting up a flood coolant system on my old 14-1/2" South Bend lathe. I bought a cheap 3gal tank+pump from Enc...
1 comments posted 22yrs
posted by spam
1 comments posted 22yrs posted by spam

Victor type 17 torch tips

Hi all Anyone know of aplace that sells victor type 17 welding tips (for J type torch), preferably in Florida or online...
4 comments posted 22yrs
posted by tharkaduso
4 comments posted 22yrs posted by tharkaduso

Lathe Spindle Oil Filter

I'm in the final stages of putting back together my Clausing Colchester 13" machine. I've cleaned off 30 years worth of...
10 comments posted 22yrs
posted by gradstdnt_99
10 comments posted 22yrs posted by gradstdnt_99

welding equipment recommendation

Hello all- I am completely ignorant when it comes to welding, welding supplies, and metalwork in general (although I do...
4 comments posted 22yrs
posted by kevinelliot
4 comments posted 22yrs posted by kevinelliot

OT: Kerosene or #1 fuel oil source in SF Bay Area?

Help its cold in here. Time to fire up the kerosene shop heater but can't find a source for cheap kerosene. San Francisc...
0 comments posted 22yrs
posted by shakascaregiver
0 comments posted 22yrs posted by shakascaregiver

Anodizing question

To help feed the boat kitty I import a very fine boat anchor from Tunisia. Arguably the best performing anchor made. Th...
12 comments posted 22yrs
posted by gashmore
12 comments posted 22yrs posted by gashmore

Making holes in aluminum sheetmetal

This will probably be boringly obvious to most readers, but I'll post it in the hope that it might be useful to a few b...
13 comments posted 22yrs
posted by SPAMBLOCKdforeman
13 comments posted 22yrs posted by SPAMBLOCKdforeman

Flashlights

Has anyone upgraded their flashlight with the new Xenon bulbs. Comments..... I'm amazed that the CSI guys can spot a sl...
48 comments posted 22yrs
posted by fordnut
48 comments posted 22yrs posted by fordnut

Other Tool Supplier's Warranties

Recently there was a thread discussing Snap-On and Sears warranty on sockets, ratchets..... I was wondering if anyone h...
4 comments posted 22yrs
posted by sam-hood
4 comments posted 22yrs posted by sam-hood

cold liquid metal

Hello, I was just wondering of anyone could offer any information at all on cold liquid bronze, brass, or copper. Somet...
23 comments posted 22yrs
posted by rvanam
23 comments posted 22yrs posted by rvanam

Home brew bandsaw now under power

And it works great. Its just a tad bit too slow nowe, but I have a faster motor as well as 3 or 4 more larger sized pul...
4 comments posted 22yrs
posted by chipmkr
4 comments posted 22yrs posted by chipmkr

'tis the time of year to think of making BBQ tools

Any suggestions on finishes other than chrome? I'm hoping there is a finish I can do myself. I'm talking about hotdog fo...
16 comments posted 22yrs
posted by gspaff
16 comments posted 22yrs posted by gspaff