⏣ General Metalworking

30778 Threads Posts
to

Max table load on a mill

I have a Bridgeport type mill from Taiwan 10X50 table size. What is the maximum load I can put on the mill and still be...
2 comments posted 22yrs
posted by we
2 comments posted 22yrs posted by we

Chopper Buildoff

I watched most of two of the chopper buildoff shows on Discovery last night. A couple of comments: They place so much e...
8 comments posted 22yrs
posted by rleonard
8 comments posted 22yrs posted by rleonard

dissasembling acetylene reg - got stumped

Hi all I cant see how to lift the rubber diaphragm without tearing it. Or it is supposed to be torn and a new one replac...
7 comments posted 22yrs
posted by tharkaduso
7 comments posted 22yrs posted by tharkaduso

OT : Kerosene space heaters

I have a "Master" Kerosene space heater and the other day I filled it with diesel thinking it would be a lot cheaper. I...
13 comments posted 22yrs
posted by habbi
13 comments posted 22yrs posted by habbi

What kind of forge do you have?

Anyone own a NC Tools Whisper series forge? Pros/cons? Other suggestions for a turnkey forge that is better? I need it...
16 comments posted 22yrs
posted by desert6traveler
16 comments posted 22yrs posted by desert6traveler

What is the proper tool/method

of dressing the green silica(?) grinding wheels used for Carbide lathe tools? Many thanks. Roger in Vegas Pets have owne...
35 comments posted 22yrs
posted by rhull
35 comments posted 22yrs posted by rhull

unbreakable shear pin on Vectrax Lathe

Here is a question for a machinery design engineer or bright lathe operator. Hopefully you are familiar with a typical...
21 comments posted 22yrs
posted by balesmachine
21 comments posted 22yrs posted by balesmachine

If you were building the dream shop

I'm looking into expanding my current shop. I would like some input from recent shop projects. Comments on things you d...
67 comments posted 22yrs
posted by gjrepesh
67 comments posted 22yrs posted by gjrepesh

Mars Probe on NASA tv

i am guessing this probe landed yesterday, there is sporatic coverage on the Nasa channel, tapes of the JPL controllers...
11 comments posted 22yrs
posted by loren
11 comments posted 22yrs posted by loren

Threading brass rod

I have no doubt that I am either being impenetrably stupid, or just confused , but is there any off the shelf, IE MSC,...
7 comments posted 22yrs
posted by j.bergstrom
7 comments posted 22yrs posted by j.bergstrom

Water vs Oil Hardening (Drill rod)

I've been using drill rod as cheap ways for roller bearings. I've always bought oil hardened, but water is cheaper. What...
4 comments posted 22yrs
posted by pminmo_spam
4 comments posted 22yrs posted by pminmo_spam

Garvin Mill Table Repair

Just dropped some photos of my Garvin Horizontal Mill into the dropBox in hopes that someone could recommend some repai...
8 comments posted 22yrs
posted by datac
8 comments posted 22yrs posted by datac

Anybody disassemble a Starrett 120 caliper?

I would like to take mine apart for a cleaning and inspection. If you have knowledge of how to do this, can you post som...
1 comments posted 22yrs
posted by spencer313
1 comments posted 22yrs posted by spencer313

Plans for a Hossfeld type bender?

Anyone have or know of where I can find plans to build a Hossfeld type tubing bender? TIA Ben
1 comments posted 22yrs
posted by b.eadie
1 comments posted 22yrs posted by b.eadie

Be careful!

Just got a request for private information from "ebay", which, of course, was not from them. I forwarded the bogus emai...
1 comments posted 22yrs
posted by vordos
1 comments posted 22yrs posted by vordos