⏣ General Metalworking

30778 Threads Posts
to

Done Moving machines and cargo weights

Hello everyone, I have completed this task and it was not easy. Can a single man move 5 milling machines by himself wit...
7 comments posted 22yrs
posted by _v8tr4_
7 comments posted 22yrs posted by _v8tr4_

Winding Wire ?

I am building some decorative iron pieces. I want to use some heavy wire, like 1/8" and bigger to wrap some of the conn...
4 comments posted 22yrs
posted by desert6traveler
4 comments posted 22yrs posted by desert6traveler

Smart Brown Model A

I ordered a manual, and it doesn't have much in it about oiling. Does anybody know where the spindle bearing sump drain...
0 comments posted 22yrs
posted by kade
0 comments posted 22yrs posted by kade

Bending wire

Seeking good advice, opinions, anecdotes or full-on rants about forming an eye, about 1/4 inch inner diameter, at the e...
2 comments posted 22yrs
posted by tedbennett
2 comments posted 22yrs posted by tedbennett

were to find tsp (again)

i went to home depot and they look at me as if i had hoof and pulled in on a sleigh. does it have a trade name or produc...
8 comments posted 22yrs
posted by asp3211968
8 comments posted 22yrs posted by asp3211968

FS: Harbor Freight 7" x 10" PRECISION MINI LATHE

I have for sale the Harbor Freight 7" x 10" PRECISION MINI LATHE . Purchased at Harbor Freight in Orlando FL. The lathe...
5 comments posted 22yrs
posted by rmo7hatespam
5 comments posted 22yrs posted by rmo7hatespam

KO Lee 612 surface grinder questions

I'm in the market for a surface grinder small enough to get into the basement shop and came across a KO Lee 612 that lo...
5 comments posted 22yrs
posted by MichaelHenry
5 comments posted 22yrs posted by MichaelHenry

Angle grinders

i bought one of those cheap 4 1/2 angle grinders from harbor freight a few weeks ago... i played around with it cutting...
6 comments posted 22yrs
posted by jim
6 comments posted 22yrs posted by jim

diesel for home heating boiler

In an emergency could you put kerosene or diesel in your home oil heating tank? Would it cause any damage?
14 comments posted 22yrs
posted by habbi
14 comments posted 22yrs posted by habbi

Drive-shaft Welding Lathe For Sale

Guys I need some help here. I won an auction on eBay for a drive-shaft welding lathe, but it is in Michigan, and I am i...
4 comments posted 22yrs
posted by ernie
4 comments posted 22yrs posted by ernie

Advantages to different air coupling types?

When I started my air tools collection a few years back I went with the "automotive" type couplers. Guy at the bearing...
6 comments posted 22yrs
posted by gto69ra4
6 comments posted 22yrs posted by gto69ra4

OT: New Compaq *&^%$#!

Last Saturday my faithful old 500 mhz homebuilt computer finally bit the dust (insert long story of how I figured out t...
34 comments posted 22yrs
posted by carl.byrns
34 comments posted 22yrs posted by carl.byrns

Strength of tubing?

Can anyone tell me the safe working load and/or failure point of some rectangular tubing, or point me to a web page? Bo...
2 comments posted 22yrs
posted by croq
2 comments posted 22yrs posted by croq

washdown motor for VFD

Just had a scrounging-related thought and wondered. VFD users have to contend with motor overheating when running at ve...
4 comments posted 22yrs
posted by bobp
4 comments posted 22yrs posted by bobp