⏣ General Metalworking

30779 Threads Posts
to

What can you create from uranium?

I have lots of uranium, want to build something.
16 comments posted 22yrs
posted by shane_d_maudiss
16 comments posted 22yrs posted by shane_d_maudiss

Sharpening woodruff cutters

I use woodruff cutters and have trouble sharpening them. Does anyone have a jig or know of a sharpening device on the m...
1 comments posted 22yrs
posted by cuezilla
1 comments posted 22yrs posted by cuezilla

Cabin Fever Expo (updated 20 Nov 2003)

A reminder. (Updated 20 Nov 2003) Cabin Fever Expo January 17-18, 2004 York Expo Center York, Pennsylvania http://logan...
0 comments posted 22yrs
posted by ssl
0 comments posted 22yrs posted by ssl

Combined Groups Get-Together/Holiday Open House

You are all cordially invited to an open house/gab session/meet 'n' greet. Get together with the list members and other...
0 comments posted 22yrs
posted by ssl
0 comments posted 22yrs posted by ssl

FS: "Metals Handbook" Vol 1 & 2

for sale: the massive "Metals Handbook", two separate volumes: Volume I: "Properties & Selection" of Metals, 8th editio...
1 comments posted 22yrs
posted by btuttleman
1 comments posted 22yrs posted by btuttleman

Using propane to start a chainsaw?

Way back when (Fri, 15 Aug 2003 06:23:05 to be precise) in rec.crafts.metalworking , nick hull was inspired to utter: >...
21 comments posted 22yrs
posted by phamp
21 comments posted 22yrs posted by phamp

Forging info needed

I need a few hundred of these s hooks out of 1/4" square bar or smaller: http://www.guadalupeforge.com/hanforirsmal1.ht...
10 comments posted 22yrs
posted by desert6traveler
10 comments posted 22yrs posted by desert6traveler

Best place to buy used tabletop gear?

Looking for a GOOD tabletop (I have a space 4' x 2' on a table that I can use) lathe and/or mill. Preferably Hardinge,...
0 comments posted 22yrs
posted by eric343
0 comments posted 22yrs posted by eric343

Repairing cast iron manifold

I have a couple of exhaust manifolds that the DPO tried to drill out broken studs and did a royal job of screwing every...
4 comments posted 22yrs
posted by gmasterman
4 comments posted 22yrs posted by gmasterman

OT Environmentalists may be in deep Kimchee

http://www.worldnetdaily.com/news/article.asp?ARTICLE_ID=35862"25 States allow anyone to buy a gun, strap it on, and wa...
493 comments posted 22yrs
posted by gunner
493 comments posted 22yrs posted by gunner

Shelving Advice Needed

i am pretty savvy, wrt to shelving, and have assembled and built it all of my adult life, just about every type for loa...
4 comments posted 22yrs
posted by loren
4 comments posted 22yrs posted by loren

Wobbly drill press

I recently picked up a fairly old (late 1970's) 16" Taiwanese drill press of unknown history. Now that it's set up, pne...
8 comments posted 22yrs
posted by speffSNIP
8 comments posted 22yrs posted by speffSNIP

Cold bending of 8mm steel

Could someone please tell me what the general rule is for cold bending mild steel plate/bar (8mm thick and approx 50mm...
2 comments posted 22yrs
posted by kenhunt
2 comments posted 22yrs posted by kenhunt

lighting contactor on motor?

Let me preface this for the electrically less experienced. Electric motor windings are inductive in nature - that is, t...
3 comments posted 22yrs
posted by grantNOSPAM
3 comments posted 22yrs posted by grantNOSPAM

Filling holes in sheet steel

i am looking to fill some holes about 3/8", irregular shaped, in 1/4" thick steel plates. Anyone have any suggestions f...
18 comments posted 22yrs
posted by cusmarsh
18 comments posted 22yrs posted by cusmarsh