⏣ General Metalworking

Crown Stove Door Springs Needed

I have a brown, double door, 4 burner Crown stove. The doors no longer have their springs and fall open. They are heavy...

2 comments posted 4yrs

posted by Sima Herszaft

2 comments posted 4yrs posted by Sima Herszaft

Brush suppliers

I need a brush for the motor in a Rigid-branded shopvac. It's 250 mils by 318 mils, and about an inch long with braided...

12 comments posted 4yrs

posted by wb8foz

12 comments posted 4yrs posted by wb8foz

About My Delta bench grinder.

Hi everyone just bought a Delta bench grinder a few weeks ago & to be honest was a bargain I think ?. The problem is I...

1 comments posted 4yrs

posted by Deen79

1 comments posted 4yrs posted by Deen79

Motor Almost finished !

I still have to bolt the intake on , motor mounts and some bracketry and I'll be ready to drop Mr Motor back into his h...

5 comments posted 4yrs

posted by Snag_one

5 comments posted 4yrs posted by Snag_one

Marine batteries

After reading many nearly useless reviews I bought the only SLI31MDP that Batteries+Bulbs had, and then a hopefully sim...

6 comments posted 4yrs

posted by muratlanne

6 comments posted 4yrs posted by muratlanne

Shelf life

Today was torque-the-heads and adjust-the-valves day . Well , until I figured out the NOS TRW VL-37 tappets I have are...

0 comments posted 4yrs

posted by Snag_one

0 comments posted 4yrs posted by Snag_one

And now a word from my transmission :

I NEED A REBUILD! I dropped it off at a shop some weeks back , only to discover recently that the business had changed...

9 comments posted 4yrs

posted by Snag_one

9 comments posted 4yrs posted by Snag_one

Harrison L 6 change wheels

Wanted 127 Teeth Change wheel for the Harrison L6

0 comments posted 4yrs

posted by 0f8503901d844703eea1acecb7a4938a_2871

0 comments posted 4yrs posted by 0f8503901d844703eea1acecb7a4938a_2871

Harrison L 6 change wheels

Wanted 127 Teeth Change wheel for the Harrison L6

1 comments posted 4yrs

posted by Richard Blake

1 comments posted 4yrs posted by Richard Blake

The Rebuild Begins

I finally got the rest of my motor back on Friday ... Today was spent getting the block mounted on the stand so I could...

7 comments posted 4yrs

posted by Snag_one

7 comments posted 4yrs posted by Snag_one

Well it's about time !

Let's build a motor ! I finally got all my parts back from the machine shop today , tomorrow I start to assemble my 305...

1 comments posted 4yrs

posted by Snag_one

1 comments posted 4yrs posted by Snag_one

Throw Away Mill

Ok, I have a project I've been wanting to do for a little while. Making a short series of videos on making some useful...

29 comments posted 4yrs

posted by none

29 comments posted 4yrs posted by none

Much Better

I know I am probably cursing us to a spate of hellscape of poltico-vulgar-pseudo-reilgious-nihilism posts. I have to sa...

1 comments posted 4yrs

posted by none

1 comments posted 4yrs posted by none

Reverse D-bit ?

I'm going to be installing bushings for the primary throttle shaft on my Quadrajet carb , and have been pondering on ho...

3 comments posted 4yrs

posted by Snag_one

3 comments posted 4yrs posted by Snag_one

Thinking About Scrapping the Hurco Mill

I retrofit it, and I rebuilt it, and I repaired it many times. It still functions, but its in desperate need of repairs...

2 comments posted 4yrs

posted by none

2 comments posted 4yrs posted by none