28 comments
posted 15yrs
posted by rhvp65
⏣ General Metalworking
30754 Threads
Posts
to
OT: A glimpse of the future
From Italy, a glimpse of the future in the US if the massive governmental deficits are not brought under control and th...
3 comments
posted 15yrs
posted by gmcduffee
3 comments
posted 15yrs
posted by gmcduffee
My own action figure!
http://www.dannychoo.com/post/en/26119/Human+Cloning+in+Japan.html Did you ever want to be an action figure? I'm trying...
3 comments
posted 15yrs
posted by cavelamb
3 comments
posted 15yrs
posted by cavelamb
Voyager - there's some metal working for ya!
Note: For what it's worth... Voyager 1's position is about 97 AU. Those "billyions and billyins" of miles made me think...
1 comments
posted 15yrs
posted by cavelamb
1 comments
posted 15yrs
posted by cavelamb
Tolerance indications
Quick question regarding machining tolerances... I need to indicate dimensional tolerance on a drawing. A fork with 1.13...
7 comments
posted 15yrs
posted by cavelamb
7 comments
posted 15yrs
posted by cavelamb
Compression Float Collets or Small Chucks?
Good afternoon, I'm happy to say Teranews is finally back up and running and I can access the newsgroup again. I'm curi...
0 comments
posted 15yrs
posted by autodrill
0 comments
posted 15yrs
posted by autodrill
Spinning Metal
Think prop spinner for a model airplane (is this sounding familiar?) Assuming that I'm not turning from solid (oh, it s...
8 comments
posted 15yrs
posted by tim
8 comments
posted 15yrs
posted by tim
Holding thin shells
Think prop spinner for a model airplane. Assuming that I'm not making it out of spun metal, the obvious way to proceed...
1 comments
posted 15yrs
posted by tim
1 comments
posted 15yrs
posted by tim
Trammed the mil yesterday
It took about an hour, but I am finally done, trammed it with a dial indicator. 0.001" over about 4 inches. (diameter of...
45 comments
posted 15yrs
posted by ignoramus10056
45 comments
posted 15yrs
posted by ignoramus10056
A piece of history
Anyone here ever run one of these machines? http://i.ebayimg.com/00/$(KGrHqZ,!loE3IC4mVJ(BN99K4vB-Q~~_3.JPG Best Regards...
19 comments
posted 15yrs
posted by H.beal
19 comments
posted 15yrs
posted by H.beal
Autodesk 123D software
Download the free Beta version of Autodesk 123D modeling software. http://www.123dapp.com/
1 comments
posted 15yrs
posted by usenetreply
1 comments
posted 15yrs
posted by usenetreply
chipmunks
The damned chipmunks. Yes, I know they are cute. Yes I know there's not much meat on 'em. Yes, I know that if a cat cat...
17 comments
posted 15yrs
posted by mice42
17 comments
posted 15yrs
posted by mice42
Need high throughput pressure regulator
--OK here's the thing: I'm trying to push a good flow of propane into a flaming widget but I'm only wanting to do it at...
9 comments
posted 15yrs
posted by steamer
9 comments
posted 15yrs
posted by steamer
20 yr old Air compresor - leaking at unloader valve
My Sears 5 hp ( ok: 2 hp) belt drive compressor has been leaking at the unloader valve whenever the unit is shut of or...
9 comments
posted 15yrs
posted by aribert
9 comments
posted 15yrs
posted by aribert
Led Flashlights
Eclipse LED Flashlights is one of the companies to get the latest technology light. LED means Light Emitting Diodes. We...
0 comments
posted 15yrs
posted by samaden11
0 comments
posted 15yrs
posted by samaden11