⏣ General Metalworking

  1. Home
  2. ⏣ General Metalworking
30777 Threads Posts
to

Worth reading in ⏣ General Metalworking

Anybody here machine 17-4ph HH-1150?

So I'm starting a job machining 174-ph HH-1150. I've found lotsa info on condition H1150 but not much on HH1150. I know...
10 comments posted 15yrs
posted by tesnow
10 comments posted 15yrs posted by tesnow

What are these?

They look to be 1/16" and 3/32". Flattened surface like a sewing machine needle, but other end does not have a hole. Le...
9 comments posted 15yrs
posted by pittmanpirate
9 comments posted 15yrs posted by pittmanpirate

Ping Gunner: High speed spindle

Keep a lookout for a spindle that will do 10krpm. I need to spin a 1/32" x 6" cut-off disk to trim endbrushes. My home-...
7 comments posted 15yrs
posted by w
7 comments posted 15yrs posted by w

Best Epoxy for build-up/repair?

got a worn shaft & its coupling bushing that needs a slight build -up & re-machine. JB weld? or ? There's allot of choi...
5 comments posted 15yrs
posted by milgil
5 comments posted 15yrs posted by milgil

Another R-22 heat pump update

Thanks all for the remote troubleshooting! The cap has leads for the fan, compressor and a common. I can't find my VTVM...
16 comments posted 15yrs
posted by w
16 comments posted 15yrs posted by w

tool/yard sale gloat

I picked up a really neat piece today, a Lufkin METAL folding 48" measurer. I've seen lots of wood, but never a metal o...
12 comments posted 15yrs
posted by pittmanpirate
12 comments posted 15yrs posted by pittmanpirate

R-22 Heat Pump update

I was able to get a cylinder of R-22 and the right manifold and hoses and finally it was good enough weather to check o...
30 comments posted 15yrs
posted by w
30 comments posted 15yrs posted by w

OT:For Sale

I have a brand new N12242408 Weigman enclosure I purchased for a customer, after installing the handle for the disconne...
4 comments posted 15yrs
posted by debco99
4 comments posted 15yrs posted by debco99

strange tool

A friend gave me a bunch of old automotive tools. I knew what most of them were but this one stumps me. Any ideas? I'd...
21 comments posted 15yrs
posted by engineman1
21 comments posted 15yrs posted by engineman1

OT find electric cable

Milady has a high tunnel greenhouse project. I'm already looking at how to do better next year... This year I installed...
5 comments posted 15yrs
posted by karltownsend.NOT
5 comments posted 15yrs posted by karltownsend.NOT

Right angle gear bearings?

For a power tool like the DeWalt 18 V right angle drill. http://www.blackanddecker.com//ProductImages/PC_Graphics/PHOTO...
3 comments posted 15yrs
posted by jdoe
3 comments posted 15yrs posted by jdoe

Might be of Some Interest

Heavy surface table at Canadian Crown Assets (surplus) Pete
0 comments posted 15yrs
posted by snell-p
0 comments posted 15yrs posted by snell-p

Flexible drive shafts

I'm thinking about cobbling together something that will involve the use of a flexible drive shaft. I've found several...
6 comments posted 15yrs
posted by paul
6 comments posted 15yrs posted by paul

Engineer shopping

A wife says to her engineer husband, "Could you please go to the store for me and buy a carton of milk. And if they hav...
2 comments posted 15yrs
posted by ud233
2 comments posted 15yrs posted by ud233

What is it? Set 386

I think that I know the answer for the second item but I'm not 100% sure: http://55tools.blogspot.com/2011/04/set-386.ht...
22 comments posted 15yrs
posted by rhvp65
22 comments posted 15yrs posted by rhvp65