⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Looking for Harrison M300

I am looking for a Harrison M300 in good condition. Ideally, my preference would be for a metric gap bed machine with a...
3 comments posted 17yrs
posted by david
3 comments posted 17yrs posted by david

Metal for milling spindle?

Now that the stepper controlled dividing head (qv) is commissioned I need to manufacture a milling spindle to cut the c...
9 comments posted 17yrs
posted by invalid
9 comments posted 17yrs posted by invalid

Bigger stuff ..

Need two discs of eg mild steel, around 7 inch diameter by 2 inch thick - any ideas? Thanks, -- Peter
2 comments posted 17yrs
posted by zenadsl6186
2 comments posted 17yrs posted by zenadsl6186

keyways

consider a gear on a shaft, with a square key. Cutting the keyway on the shft is fairly easy, you can use a slotting sa...
14 comments posted 17yrs
posted by zenadsl6186
14 comments posted 17yrs posted by zenadsl6186

Stainless corner pieces ?

I'm looking for some stanless steel corners somewhat like this : http://www.adamhall.com/uk/media/products/400/4001-f1....
0 comments posted 17yrs
posted by adrian.110504
0 comments posted 17yrs posted by adrian.110504

Bridgeport Interact wanted

I'm looking for a good condition Bridgeport Interact (1 or 2) with a TNC151B or 155B or later control if anyone is aware...
4 comments posted 17yrs
posted by andrew
4 comments posted 17yrs posted by andrew

Management Tutorials

Delhi Institute of Management & Services Dear friends, We are extremely happy to welcome you to the world of Management...
0 comments posted 17yrs
posted by dimsgroups
0 comments posted 17yrs posted by dimsgroups

small air compressor for powering steam model

Gentlefolk, My Lady Stephanie is at last nearing completion, and I'd like the ability to run her occasionally for demon...
26 comments posted 17yrs
posted by junk
26 comments posted 17yrs posted by junk

ArcEuro X3

So somebody asked me to report in on the ArcEuro X3 that I bought a few weeks ago. Here goes: Ordering was a very strai...
3 comments posted 17yrs
posted by nigele
3 comments posted 17yrs posted by nigele

small canadian gloat

Reading the local at the local coffee shop instead of talking to me wife when .... woo hoo! Showed me wife - go have a...
10 comments posted 17yrs
posted by wee_mikey
10 comments posted 17yrs posted by wee_mikey

Metal engineering models

Hi Group, I'm interested in getting started on making metal mechanical devices/ model and the like. Problem is I have n...
11 comments posted 17yrs
posted by david.cawkwell
11 comments posted 17yrs posted by david.cawkwell

Thread question

There's an imperial thread that's almost exactly the same as M5 coarse - anyone know what it it is? Thanks, Peter Fairbr...
30 comments posted 17yrs
posted by zenadsl6186
30 comments posted 17yrs posted by zenadsl6186

12 volt power supply

Hi Guys, My Boxford STS10 20 lathe has a 12 volt light, but no power supply. Does anyone know where i can source a supp...
3 comments posted 17yrs
posted by mcole153
3 comments posted 17yrs posted by mcole153

Free F type collets

> 1/2" , 9/16", 5/8" > Made by Perfos > > I believe these are "F type" collets but please ask if you need more info abo...
7 comments posted 17yrs
posted by nomail
7 comments posted 17yrs posted by nomail

PTFE Washers Wanted

Could I ask if anyone in the group could turn me up some PTFE washers please? Proper coin of the realm offered in excha...
0 comments posted 17yrs
posted by peterforbes
0 comments posted 17yrs posted by peterforbes