⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Thin Tufnol Sheet?

I'm looking for small quantities (say 200x200mm) of 0.5 and 1.5mm Tufnol sheet - probably Carp brand. Ideas anyone, plea...
8 comments posted 19yrs
posted by jaford
8 comments posted 19yrs posted by jaford

Warco Mill

Hi all I am a newbie on this group. Has anyone any experience with the Warco WM-14 Variable Speed Mill. I am considerin...
6 comments posted 19yrs
posted by derek.tuckey
6 comments posted 19yrs posted by derek.tuckey

Uses for old floppy discs?

Is there a better fate for redundant floppy discs than throwing them in the bin? I'm trying to make a bit of space, got...
29 comments posted 19yrs
posted by duttondock
29 comments posted 19yrs posted by duttondock

Unimat 3

Sorry for the delay in replying - I had to go on holiday. I purchased a Unimat 4 motor from Chronos - they were very hel...
1 comments posted 19yrs
posted by sandy
1 comments posted 19yrs posted by sandy

? Stainless steel tube

Just thought it may be worth an ask on here? I am trying to find some 19mm (3/4") OD stainless tube with an internal di...
14 comments posted 19yrs
posted by adrian
14 comments posted 19yrs posted by adrian

ID Lathe Please

Hi lads ...can anyone ID this lathe ... pics say it all ... think a may have had a set of cone pulleys and a countersha...
5 comments posted 19yrs
posted by aboard_epsilon
5 comments posted 19yrs posted by aboard_epsilon

Reversing Switch

I am looking for a Dewhurst type A reversing switch in good condition for my Boxford lathe. Thank you snipped-for-privac...
1 comments posted 19yrs
posted by bernard25
1 comments posted 19yrs posted by bernard25

Looking for:Large QC30 toolholder

I'm on the lookout for a QC30 toolholder that can hold cutter shanks of 25mm/1", if they are available. ( this is to hol...
2 comments posted 19yrs
posted by emimec
2 comments posted 19yrs posted by emimec

Kress invent the collet

Just been searching around for some smaller collets for the Kress spindles and I found this http://www.patentstorm.us/p...
3 comments posted 19yrs
posted by lester
3 comments posted 19yrs posted by lester

Tripan lathe tool holder dovetail specs

Does any one have the specs for the 231 tripan dovetail only I trying to get more holders of a 3rd party supplier I thin...
3 comments posted 19yrs
posted by andrew
3 comments posted 19yrs posted by andrew

centering / edge finder camera update and thanks

Hi all after consideration and looking at the Hemmingway kit I went the electronic route as the mill is cnc I used the...
1 comments posted 19yrs
posted by andrew
1 comments posted 19yrs posted by andrew

30 3 phase .and 400v 3 ph question

could somebody set me straight ? in england do we have 230v 3 ph ,which is 230 v from each ph to th next ,and 400 to ne...
9 comments posted 19yrs
posted by ivanhoew.2xqi4n
9 comments posted 19yrs posted by ivanhoew.2xqi4n

Tool clearout

I'm rearranging my garage and so need to get rid of some stuff: Fabco Star bench mount pillar drill. Looks about 40 yea...
4 comments posted 19yrs
posted by l.s.griffiths
4 comments posted 19yrs posted by l.s.griffiths

Link Belts

Hi All I have a Boxford model B (rear motor) which has two belts - a conventional one to the countershaft and a link be...
3 comments posted 19yrs
posted by russell
3 comments posted 19yrs posted by russell

Chronos gear making DVD

Has anyone seen the Chronos gear making DVD and is it any good? http://tinyurl.com/ypcdom AWEM
31 comments posted 19yrs
posted by andrew
31 comments posted 19yrs posted by andrew