⚙ Model Engineering in the UK

Eagle Grinder Size and weight

Please could someone give me an idea of the size and weight of an Eagle Surface Grinder. I have been offered one (over...

3 comments posted 19yrs

posted by jontom_1uk

3 comments posted 19yrs posted by jontom_1uk

A sorry sight!

Once again on a trip into a container yard off Hyde Rd Manchester where two decent looking lathes. A Colchester Master,...

1 comments posted 19yrs

posted by adrian

1 comments posted 19yrs posted by adrian

Removing small roll pins

I need to remove some small roll pins (1/16" and 3/32") and am unable to think of a simple, non-brutal, method So far I...

10 comments posted 19yrs

posted by newsreader

10 comments posted 19yrs posted by newsreader

Part P petition

Those of you with views on the 'part P' electrical regulations may be interested to hear that there is a petition for it...

57 comments posted 19yrs

posted by andrew

57 comments posted 19yrs posted by andrew

Hydraulic lever valve block

I have just posted an ad on John's 'Model Engineering Advert Pages' .. and thought it wouldn't do any harm to repeat it...

0 comments posted 19yrs

posted by ieb

0 comments posted 19yrs posted by ieb

nicky.tayler@ntlworld.com

Hi its only me, just checking your e-mail system is working o/k Dad

4 comments posted 19yrs

posted by salamanda

4 comments posted 19yrs posted by salamanda

Engineering plastics: - Delrin??

OK I know my memory is going so I need help here. Many years ago I bought some red rod! I could have bought green or bl...

14 comments posted 19yrs

posted by adrian

14 comments posted 19yrs posted by adrian

Coolant pumps etc.

I'd had a frustrating 3 days with no power. On Thurs & Fri I told myself I could catch up a bit with work at the weeken...

2 comments posted 19yrs

posted by duttondock

2 comments posted 19yrs posted by duttondock

Steel Balls

Any suggestions in the uk preferably mail /internet order 3.5mm size Thanks Andrew Bishop

11 comments posted 19yrs

posted by andrew

11 comments posted 19yrs posted by andrew

Advice on milling depth/width/feed of cut for novice!

Hi All, Had my first real go on the Marlow yesterday making up some T-nuts for it (awkward 7/16" width). I got there in...

5 comments posted 19yrs

posted by robs1972

5 comments posted 19yrs posted by robs1972

OT Brake disk retaining screw size?

On trying to do a simple job for a friend, I need to drill a hub back plate to take the small countersunk screw that ho...

6 comments posted 19yrs

posted by adrian

6 comments posted 19yrs posted by adrian

117 passes and still scraping ... :-(

Hi! I need some moral support! :-) Got me a manual surface grinder last September or so. When trying to adjust the gibs...

11 comments posted 19yrs

posted by muellernick

11 comments posted 19yrs posted by muellernick

Warco Mill trips RCD!

Hello everyone, I recently was given a old Warco Milling machine in fantastic condition. I installed this into my works...

11 comments posted 19yrs

posted by Jason.jwcw

11 comments posted 19yrs posted by Jason.jwcw

Collet Identity Help

I've got some collets lying around that are similar to 5C in conception but different dimensions. The main shank is 27m...

3 comments posted 19yrs

posted by charles.ping

3 comments posted 19yrs posted by charles.ping

A Little Workshop Electrical Advice

Hoping that not everyone is in London enjoying themselves and spending all their pocket money on essential goodies and...

11 comments posted 19yrs

posted by jontom_1uk

11 comments posted 19yrs posted by jontom_1uk