⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6652 Threads Posts
to

Richmond dividing head

I have a 5" Richmond dividing head with the drive spindle etc for differential indexing (but alas no gears) I'm going t...
1 comments posted 20yrs
posted by charles.ping
1 comments posted 20yrs posted by charles.ping

toolpost material

A while ago someone was asking here about the best material to make a lathe toolpost from, but I can't find the thread....
18 comments posted 20yrs
posted by zenadsl6186
18 comments posted 20yrs posted by zenadsl6186

newbie milling machine help

Have had an Elliot sturdimill 1250 for a while now but it has never been installed - hope to do so soon. It is in great...
1 comments posted 20yrs
posted by cysult.nospam
1 comments posted 20yrs posted by cysult.nospam

ME Thread Data

Gentlemen, I have looked at various Web sites for data on ME threads but cant find any thing of use, i.e. tapping size,...
7 comments posted 20yrs
posted by martin.perman
7 comments posted 20yrs posted by martin.perman

Cromwell Lathe

Is anyone aware of articles on the Cromwell lathe circa 1950s? I have recently acquired one, and a copy of the handbook...
0 comments posted 20yrs
posted by oldnoccer
0 comments posted 20yrs posted by oldnoccer

New Project Atlas Bearing Replacement

Just planning to move on to the next "clearout" project and need some advice if possible. I have had an old Atlas 10f u...
27 comments posted 20yrs
posted by jontom_1uk
27 comments posted 20yrs posted by jontom_1uk

Myford Painting

Hi All, In relation to my other thread I am restoring a Myford super 7. I hav the Myford paint and wondered. Should i a...
1 comments posted 20yrs
posted by colinheath.25k1cb
1 comments posted 20yrs posted by colinheath.25k1cb

Ingenuity

Spotted this whilst having a trawl on e-bay (item no. 7605733134) http://tinyurl.com/o65c5 Never seen a lathe fitted wi...
19 comments posted 20yrs
posted by panuno95-ukrec
19 comments posted 20yrs posted by panuno95-ukrec

5c as a Push collet?

I picked up a Schaublin 120 second-op lathe yesterday, bought off ebay with the intention of robbing the capstan assemb...
0 comments posted 20yrs
posted by duttondock
0 comments posted 20yrs posted by duttondock

Making PCB's

For those of you into making PCB's (printed circuit boards) I have put another sacrifice to the moving house deities up...
16 comments posted 20yrs
posted by andrew
16 comments posted 20yrs posted by andrew

On the scrounge

I have just bought a load of relays to begin the signalling of the Lackham Museum and Woodland Railway (see www.lmandwr...
5 comments posted 20yrs
posted by peter
5 comments posted 20yrs posted by peter

tap and die toolmakers question

Normally a tap will cut a thread that's a bit bigger than the thread a matching die will cut, so there is a small gap b...
4 comments posted 20yrs
posted by zenadsl6186
4 comments posted 20yrs posted by zenadsl6186

Tool steel rod

Anybody know where I can get a couple of 6" lengths of tool steel (HSS or cobalt) ground down to 13/64" diameter?
12 comments posted 20yrs
posted by tim
12 comments posted 20yrs posted by tim

Myford Spindle

The discussion on scraping a bed prompts me to ask about my Super-7 spindle. Very early in the life of this machine, no...
11 comments posted 20yrs
posted by charles
11 comments posted 20yrs posted by charles

ML7 Pulley Sleeve Gear

Made an interesting discovery when I pulled apart the old spindle on my ML7 tonight. Unless I'm mistaken (always possib...
2 comments posted 20yrs
posted by panuno95-ukrec
2 comments posted 20yrs posted by panuno95-ukrec