⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

Part-built 3 1/2" Ivy Hall

I'm not in the 3 1/2" circles, and I have this for disposal. (Inherited, not made by me) There is a running chassis, a...
10 comments posted 20yrs
posted by aiyr.r.bean
10 comments posted 20yrs posted by aiyr.r.bean

same hole again

I need to drill and ream a 4 mm dia 55 mm deep hole in Inconel X-750, which is hard as something-or-other, a lot harder...
8 comments posted 20yrs
posted by zenadsl6186
8 comments posted 20yrs posted by zenadsl6186

ALDI Special

ALDI are doing a Dremel type tool with flexible drive for £14.99 - Extremely versatile, ?exible combi tool for the DIY...
5 comments posted 20yrs
posted by steve.withnell
5 comments posted 20yrs posted by steve.withnell

OTish: a silly bit of metrication

As part of the day job, tomorrow I have to drill about 100 holes for 12mm bolts through 7" thickness of hardwood, with...
22 comments posted 20yrs
posted by duttondock
22 comments posted 20yrs posted by duttondock

Adcock & Shipley 1ES

Anyone with one of these fitted a DRO, if so I'd love to see a photo of how you mounted the scales. Regards Kevin
2 comments posted 20yrs
posted by kevin.newsgroups
2 comments posted 20yrs posted by kevin.newsgroups

Odd ball request for supplier info - door seal

Dear All Slightly odd request, but I am sure someone may have a answer as I am looking for a high temperature seal, my...
7 comments posted 20yrs
posted by davidi1107
7 comments posted 20yrs posted by davidi1107

Model Engineer 15th Nov 1968

My American friend wishes to find out about the "Loyal" cycle engine. Before he buys a years copies from E Bay he would...
1 comments posted 20yrs
posted by davecroft
1 comments posted 20yrs posted by davecroft

Boring a deep hole

I'm trying to bore 2 journals in a cast iron part; the journals are 1 3/4" but badly worn; I intend to bore them oversi...
8 comments posted 20yrs
posted by aholeintheground
8 comments posted 20yrs posted by aholeintheground

Spot welder wanted

Looking for a portable 'squeeze' type spot welder. My ancient one has had a squeeze too many ! AWEM
0 comments posted 20yrs
posted by andrew
0 comments posted 20yrs posted by andrew

Cleaning fluids

For the small amount of cleaning of parts etc that I do I prefer to use 500ml spray cans of solvent. Since 111 Trichlor...
47 comments posted 20yrs
posted by Clockie
47 comments posted 20yrs posted by Clockie

Clearout

I'm having a bit of a clearout at work, and have found some scrap (to us) old machine components. They will go in the s...
0 comments posted 20yrs
posted by panuno95-ukrec
0 comments posted 20yrs posted by panuno95-ukrec

X2 cnc conversion

Has anyone done an X2 conversion? An improved dog implied that a cynical trader was in the process of, but that was som...
6 comments posted 20yrs
posted by zenadsl6186
6 comments posted 20yrs posted by zenadsl6186

10 mm collets

Can anyone suggest where I might buy 10 mm collets (sometimes known as D collets) to suit my old Pultra clock makers la...
5 comments posted 20yrs
posted by clifford
5 comments posted 20yrs posted by clifford

Acme Rod

I'm after a short length of 3/4" x10 tpi LH acme rod. The usual sources (Halifax & Kingston) have drawn a blank. Ay othe...
6 comments posted 20yrs
posted by charles.ping
6 comments posted 20yrs posted by charles.ping

Source of Imperial oil seals?

I need to replace some seals on an Alexander T&C grinder I'm rebuilding. In both cases the seals operate on sliding sha...
5 comments posted 20yrs
posted by mike.crossfield
5 comments posted 20yrs posted by mike.crossfield