⚙ Model Engineering in the UK

  1. Home
  2. ⚙ Model Engineering in the UK
6651 Threads Posts
to

Worth reading in ⚙ Model Engineering in the UK

O/A gas cylinder costs

Hi all, Could anybody give me an idea as to how much oxy/acetylene cylinders cost to rent and refill? I do not foresee...
7 comments posted 21yrs
posted by anton_600
7 comments posted 21yrs posted by anton_600

reverse switch wiring ?

hi all my ml7 came with a dewhurst and partner reverse switch ,but onl ran in fowards . ive followed the diagram in the...
8 comments posted 21yrs
posted by willowkevin.1innkc
8 comments posted 21yrs posted by willowkevin.1innkc

Curious Silicone Sealant

I used some old rtv silicone on friday, I knew it was past it's best as I had to pull a load of solid out of the cartri...
8 comments posted 21yrs
posted by markgengine
8 comments posted 21yrs posted by markgengine

DZynSource - An Industry Resource

I have written a piece of software to help mold designers, tooling engineers, moldmaker, toolmakers, and plastics profe...
0 comments posted 21yrs
posted by moldzine
0 comments posted 21yrs posted by moldzine

Chris Heapy

It is concerning that Chris has apparently not been in circulation since 16th December - I know in recent months he mus...
3 comments posted 21yrs
posted by andrew
3 comments posted 21yrs posted by andrew

Advice needed on Rapidor Saw

Thanks to Bob Minchin I have recently acquired a nice Rapidor Major power hacksaw at a bargain price (thanks again Bob)...
42 comments posted 21yrs
posted by mike.crossfield
42 comments posted 21yrs posted by mike.crossfield

OT:Tusunami Appeal Red Letter day raffle.

I'm trying to raise funds for the Appeal. If you fancy a punt with a 1 in 40 or better chance of winning then please ha...
1 comments posted 21yrs
posted by bob.minchin
1 comments posted 21yrs posted by bob.minchin

What does the team think?

An associate and I are puzzled as to the correct direction to fit a blade into a Manchester Rapidor power hacksaw. Logi...
6 comments posted 21yrs
posted by bob.minchin
6 comments posted 21yrs posted by bob.minchin

Confused of eBay

While looking for something else, I saw this on eBay (http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=14737&it...
0 comments posted 21yrs
posted by jc.nospam
0 comments posted 21yrs posted by jc.nospam

New version of Newsblock released.

Email if you need the new version. This one will go thru all previously sent mails to get rid of anything filtered. John...
2 comments posted 21yrs
posted by john
2 comments posted 21yrs posted by john

Stuart Turner Kits

Just wondered what the general opinion was of Stuart Turner stationary steam kits was. I bought Dad an S50 as a set of...
8 comments posted 21yrs
posted by steve.withnell
8 comments posted 21yrs posted by steve.withnell

Model steam engines?

Several years ago I started to build two 5 inch gauge locomotives, a Netta and a Pansy, but I got to a point where I ha...
0 comments posted 21yrs
posted by alan.holmes
0 comments posted 21yrs posted by alan.holmes

Linisher Settings?

I was given a B&Q sander/linisher in my Xmas Stocking. However, the accompanying instructions are remarkable by their p...
3 comments posted 21yrs
posted by me
3 comments posted 21yrs posted by me

Cutting an acme nut

I have tracked down the source of slop in the cross slide on my Dore-Wesbury milling machine to the thread in the nut b...
10 comments posted 21yrs
posted by steve
10 comments posted 21yrs posted by steve

CNC router software

Hi everyone out there! I wondered if anyone owning a cnc router could give me advice on th piece of code I wrote for my...
6 comments posted 21yrs
posted by pier.1ii94b
6 comments posted 21yrs posted by pier.1ii94b