⚡ Welding Forums

  1. Home
  2. ⚡ Welding Forums
6253 Threads Posts
to

Worth reading in ⚡ Welding Forums

Playing with the gophers today

Ahhh. Spring has sprung. The trees have all blossomed and turned to leaves. And the gophers are out. I tried my new dev...
4 comments posted 18yrs
posted by pittmanpirate
4 comments posted 18yrs posted by pittmanpirate

Basic Equip Needs for SMAW Arc Welding?

Another newbie question, folks. I searched but didn't find this exact question addressed. I'm thinking of getting a sti...
12 comments posted 18yrs
posted by at
12 comments posted 18yrs posted by at

Metal corrosion question

I want to use some free pieces of granite to make water features. This will probably evolve or go down in flames, but I...
2 comments posted 18yrs
posted by pittmanpirate
2 comments posted 18yrs posted by pittmanpirate

Baby pictures ........

My new baby ..... well, a little used ........ http://www.flickr.com/photos/deserttraveler/ Still going to put the vise...
17 comments posted 18yrs
posted by pittmanpirate
17 comments posted 18yrs posted by pittmanpirate

Trailer tongue tool box question

I need a toolbox on my welding trailer, and have found out that they make odd shaped ones for trailer tongues. I am ver...
2 comments posted 18yrs
posted by pittmanpirate
2 comments posted 18yrs posted by pittmanpirate

Interesting item I found in trailer parts catalog

It is called an "axle slider". Maybe someone can correct me if wrong, but all it looks like is a section of angle iron...
17 comments posted 18yrs
posted by stryped
17 comments posted 18yrs posted by stryped

I'm Back!!!!!

Well it turns out that a lot of the ISP updated their newservers and became incompatible with older newsreaders. I had...
3 comments posted 18yrs
posted by ernie
3 comments posted 18yrs posted by ernie

A metal table project

Here is a picture of a table I just finished. The frame is powder coated steel tube with Mexican tile as the top. http:...
2 comments posted 18yrs
posted by WanderingMetalHead.DUMP.SPAM
2 comments posted 18yrs posted by WanderingMetalHead.DUMP.SPAM

An equation of variables.........

My neighbor came to me today to ask that I weld a couple of grab hooks onto the bucket of his Massey Ferguson front end...
5 comments posted 18yrs
posted by pittmanpirate
5 comments posted 18yrs posted by pittmanpirate

Tensile stregth of bolt. (Trying to learn)

I have posted about building a trailer. Would like to weld and bolt the A frame underneath the actual trailer. (For mor...
14 comments posted 18yrs
posted by stryped
14 comments posted 18yrs posted by stryped

Welding 20/22ga with a 251?

I've got a job were I'm going to be welding a lot of 20 and 22 guage 304 stainless. (Ok, a lot means about 50-100 piece...
0 comments posted 18yrs
posted by torin
0 comments posted 18yrs posted by torin

Tongue design question

Been thinking of building a small dual axle trailer. I have available to be 4x4 =BC inch steel tubing at scrap price. A...
8 comments posted 18yrs
posted by stryped
8 comments posted 18yrs posted by stryped

REQ: hammer restoration

I bought an old hammer head with very rounded striking faces. I would like to rebuild the faces. What would be the best...
4 comments posted 18yrs
posted by devnull
4 comments posted 18yrs posted by devnull

110vt buzzbox questions

Years ago, at least 20, I snagged an elderly Marquette 110vt buzzbox. Its always been an utter pain in the ass to weld...
10 comments posted 18yrs
posted by gunner
10 comments posted 18yrs posted by gunner

7018 rods question

I was reading on the Miller website an explanation of rods. It said that 7018 rods are "not recommended for use in smal...
47 comments posted 18yrs
posted by stryped
47 comments posted 18yrs posted by stryped