⚡ Welding Forums

TIG rod "Snap-Lock system" : Patent for sale!!

Did you also ever wander how to deal with the expensive loss, caused by stub-ends of TIG welding rods? Did you ever rea...

5 comments posted 21yrs

posted by hcdegoey

5 comments posted 21yrs posted by hcdegoey

WTB: Co2 Flow meter

Hope this is OK to post here .... I am just getting into MIG welding, and I'm looking to try solid wire on my hobby wel...

3 comments posted 21yrs

posted by rx7trex

3 comments posted 21yrs posted by rx7trex

stainless to steel

I have a Hobart Handler 175 MIG and I need to weld some stainless steel plates onto steel angle iron and it's something...

2 comments posted 21yrs

posted by faust8098

2 comments posted 21yrs posted by faust8098

work shop storage

I am in the process of rearranging my shop layout....what shop storage method do you like the best in your shop. For ex...

12 comments posted 21yrs

posted by bruce

12 comments posted 21yrs posted by bruce

TIG Braze Welding Tooth Back onto Gear...PING Ernie

I have the spindle out of the lathe and the bull gear has a tooth that is broken. Part of the tooth is still there and...

5 comments posted 21yrs

posted by Sierevello

5 comments posted 21yrs posted by Sierevello

Home wiring and plugging in a welder

I would like to plug a 220V welder into my dryer outlet, since that is the only 220V outlet I have. But the house I'm r...

25 comments posted 21yrs

posted by no_spam

25 comments posted 21yrs posted by no_spam

Mig Co2/Argon gas flow rate?

I just installed a Mig conversion gas kit on my Lincoln Weld pac 100, nowhere does it specify in the manuals, the flow...

3 comments posted 21yrs

posted by RotorHead1

3 comments posted 21yrs posted by RotorHead1

TIG welding help

Greetings all, I'm not an expert welder, but I've done enough to have an idea of what's going on. I've just migrated to...

8 comments posted 21yrs

posted by jcreid

8 comments posted 21yrs posted by jcreid

alpaz cutter welder

Hi all, I've read about this unit that Don had in the past. Does anyone have one for sale? I'd really like to get my han...

0 comments posted 21yrs

posted by djmartins

0 comments posted 21yrs posted by djmartins

plasma cutter filter

There was a thread recently about how to extend the life of plasma consumables. Check this new unit out. I haven't tried...

0 comments posted 21yrs

posted by carter

0 comments posted 21yrs posted by carter

Bending Perfect Rings??? Help!!!

I have tried to use my bender to make 14" perfect rings out of 1/4 inch steel rod, however I keep having the same probl...

3 comments posted 21yrs

posted by bonettes

3 comments posted 21yrs posted by bonettes

Rod question

I had to go to a sheet metal fab shop today. While there, I smelled the familiar odor of welding rods burning. As I wal...

15 comments posted 21yrs

posted by deserttraveler

15 comments posted 21yrs posted by deserttraveler

Ernie.....Question??

Why do you MIG with CO2 but not TIG? I'm sure that there is a scientific answer! Thanks Mike

5 comments posted 21yrs

posted by mcrump1

5 comments posted 21yrs posted by mcrump1

Plasma, TIG, MMA unit questions

Hi there, I'm new to the group and pretty new on welding. I MIG and gas at the moment and am wanting to buy a plasma cu...

6 comments posted 21yrs

posted by gay

6 comments posted 21yrs posted by gay

Low current welders, fine work, jewelry, etc.

There was a thread recently that touched on jewelry welding. I think the person asking the question wanted to know abou...

1 comments posted 21yrs

posted by 2regburgess

1 comments posted 21yrs posted by 2regburgess